verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ32X50-50S

The AirTAC SEJ Adjustable Cylinder SEJ32X50-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø32mm unit covers an effective stroke of 0–50mm without changing cylinders. Force is equal in both directions.

  • BoreØ32 mm
  • Nominal stroke50 mm
  • Adjust window50 mm
  • Effective stroke0–50 mm
  • Port sizePT1/8
  • CushionAdjustable, 27 mm
$66.03 $73.53Save 10% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SEJ32 stroke, mounting and version on one page All SEJ32 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SEJ Adjustable Cylinder SEJ32X50-50S

The AirTAC SEJ32X50-50S is a double-acting, double-rod ISO 15552 profile cylinder with a 50mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so the output force is perfectly equal in both directions at 345 N each way at 0.5 MPa. The retract stroke dials from 0 up to 50mm via a back-rod stop screw, letting you fine-tune the exact end position on the machine without swapping hardware.

This 32mm bore unit features a PT1/8 port, a Ø12mm rod with an M10x1.25 thread, and an integrated magnet (-S) for CMSE reed or DMSE electronic sensors. Adjustable air cushions at both ends decelerate the load near stroke end, while the extruded aluminum ISO 15552 body omits external tie rods for a clean profile.

Airtac SEJ Adjustable Cylinder SEJ32X50-50S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ32X50-50S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ32 mm
Nominal stroke50 mm
Adjustment window50 mm (0–50 mm)
ConfigurationDouble rod, double acting
Port sizePT1/8
Rod threadM10×1.25
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 27 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø32mm)

PressureForce (both directions)
0.5 MPa346 N
0.7 MPa484 N
Max (@1.0 MPa)70 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ32X50-50S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
32Bore size in mm.
×50Nominal stroke length in mm.
-50Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ32X50-50S Is Used

tune

Pick-and-Place Calibration

Dial the 0-50mm retract window to precisely set pick heights on an assembly handler, utilizing the 345N both-way force to grip and lift small electronic parts reliably.

swap_horiz

Part Changeover Stops

Adjust the mechanical end stop on a packaging conveyor when switching between varying carton lengths, avoiding hardware changes while maintaining accurate positioning.

precision_manufacturing

Trial Positioning Jigs

Fine-tune the end-of-stroke contact point on a machining jig during prototype runs, locking the back-rod stop screw once the optimal 0-50mm position is found.

Is the Airtac SEJ Adjustable Cylinder SEJ32X50-50S the Right Cylinder?

Confirm this 50mm adjustment window covers your required end-position range, as the effective stroke dials down from 50mm to 0mm. If you need less variability, a fixed-stroke SED is sufficient. For sizing both ways, stepping down is not an option as 32mm is the smallest bore, but stepping up to the 40mm bore yields 528 N both ways at 0.5 MPa if 345 N is insufficient.

When replacing an ISO 15552 cylinder, match the 32mm bore, 50mm stroke, PT1/8 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2 (the SEJ set omits FB, CA, CB, and CR). Note that the air cushion and mechanical stop screw only set the end position and decelerate the load; they do not hold position on air loss. For fail-safe holding, specify a BSED or an external rod lock.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (50mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 50mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ32X50-50S FAQ

A stop screw on the back rod lets you mechanically shorten the retract stroke over a 50mm window. The effective stroke can be dialed from 0mm up to the nominal 50mm, allowing you to fine-tune the end position on the machine and lock it in place without changing hardware.

Because it is a double-rod cylinder with equal annulus areas, the force is identical in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ32X50-50S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SEJ32X50-50S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.