
The AirTAC SEJ Adjustable Cylinder SEJ32X60-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø32mm unit covers an effective stroke of 40–60mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X60-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window, yielding an effective stroke range of 40-60mm. A rod exits both ends, ensuring the annulus area is identical in both directions. This provides equal force and speed extending and retracting, delivering 345 N each way at 0.5 MPa.
You dial in the retract end-position via a stop screw on the back rod, then lock it after setting. The extruded aluminum barrel has no external tie rods, and the -S magnet enables CMSE reed or DMSE electronic position sensing. It includes field-adjustable air cushions at both ends to decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X60-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 60 mm |
| Adjustment window | 20 mm (40–60 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×60 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20mm retract window to match varying circuit board widths, using the 345N both-way force to cleanly shear component leads without retooling.
Adjust the effective 40-60mm stroke on the fly during carton size changeovers, ensuring the double-rod maintains equal clamping speed.
Fine-tune the exact retract stop for a micro-fluidic nozzle, locking the back-rod screw after finding the perfect dispense height.
Verify the 20mm adjustment window covers your required end-position range. If you need less force, there is no smaller SEJ bore. If your application requires more thrust, stepping up to the 40mm bore yields 528 N both ways at 0.5 MPa. If your end-position never changes, a fixed-stroke SED avoids the back-rod mechanism. For drop-pressure safety, note this cylinder does not hold position on air loss; use a BSED or external rod lock. As an ISO 15552 cylinder, it dimensionally interchanges on bore, stroke, PT1/8 port, and mounting (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 20mm window. You can dial the effective stroke from 40mm up to 60mm, then lock the screw in place.
Because it is a double-rod cylinder, force is equal both ways: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.