
The AirTAC SEJ Adjustable Cylinder SEJ32X75-20SH is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø32mm unit covers an effective stroke of 55–75mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X75-20SH is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so thrust is equal both ways: 345 N at 0.5 MPa and 483 N at 0.7 MPa. The Viton (FKM) seal extends the operating temperature range up to 150 C.
A stop screw on the back rod provides a 20 mm adjustment window, letting you dial the retract stroke from 55 mm up to 75 mm. The included -S magnet supports CMSE reed and DMSE electronic sensors for position feedback. It features field-adjustable air cushions at both ends and a PT1/8 port.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X75-20SH |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 75 mm |
| Adjustment window | 20 mm (55–75 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 55 to 75 mm retract position on packaging machines, utilizing the 483 N both-way force to seat components precisely.
Quickly adjust the mechanical stop for varying product heights on a test rig, leveraging the FKM seals for 150 C thermal resistance.
Use the equal 345 N bidirectional thrust at 0.5 MPa to probe and set exact end-stops during assembly fixture prototyping.
The 20 mm retract window is ideal for fine-tuning a 75 mm end position on the machine without swapping hardware. If you need less force, the adjacent bore down delivers 345 N at 0.5 MPa, but stepping up to the 40 mm bore yields 528 N at 0.5 MPa for heavier loads. For fixed-position tasks that never require adjustment, a standard SED cylinder is sufficient. Remember, the adjustable cushion decelerates near stroke end but does not hold position on air loss; use an external rod lock for fail-safe holding. Match your ISO 15552 replacement by confirming the 32 mm bore, 75 mm stroke, PT1/8 port, and magnet options.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke within a 20 mm window. The effective stroke range is 55 mm to 75 mm, which you lock after setting your exact end position.
Because it is a double-rod cylinder, force is equal in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa. The FKM Viton seals allow operation up to 150 C.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.