
The AirTAC SEJ Adjustable Cylinder SEJ32X80-10LB is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø32mm unit covers an effective stroke of 70–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X80-10LB is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas, so it delivers an equal 345 N of thrust and pull force each way at 0.5 MPa. The rear stop screw lets you dial the retract end from 70 to 80 mm for exact positioning.
This unit includes an LB mounting bracket and uses a PT1/8 port. Because it lacks a magnet (-S), it cannot host CMSE or DMSE position sensors. Adjustable air cushions at both ends decelerate the load near stroke end, but note that a plain SEJ does not hold position on air loss.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X80-10LB |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 10 mm (70–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 70-80mm end position during setup, using the 345N both-way force to fine-tune automated assembly stops without replacing hardware.
Quickly adjust the retract stroke by up to 10mm to accommodate varying part heights on a packaging conveyor, maintaining precise equal push and pull force.
Test clamping distances on machining fixtures, leveraging the 483N equal directional force at 0.7 MPa to secure parts before finalizing the mechanical end.
The 10mm adjustment window is ideal for fine-tuning an end position during machine commissioning without swapping hardware. If you need less force, stepping down is not an option as 32mm is the smallest bore. If your application requires more power, the next bore up is 40mm, which provides 528 N both ways at 0.5 MPa. For fixed-position tasks that do not require fail-safe holding on air loss, a standard SED fixed-stroke cylinder might suffice. When replacing an ISO 15552 cylinder, verify your 32mm bore, 80mm stroke, PT1/8 port, and LB mounting footprint match. Since the stroke is under 300mm, side-load stress is minimal, but always ensure external guides support heavy lateral loads.
Quick checklist
The -10 designation means the retract stroke can be dialed down by up to 10mm using a stop screw on the back rod. This gives an effective stroke range of 70 to 80mm. You lock the screw after setting the exact end position.
Because it is a double-rod cylinder, the force is identical in both directions. It delivers 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.