verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ32X80-20S

The AirTAC SEJ Adjustable Cylinder SEJ32X80-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø32mm unit covers an effective stroke of 60–80mm without changing cylinders. Force is equal in both directions.

  • BoreØ32 mm
  • Nominal stroke80 mm
  • Adjust window20 mm
  • Effective stroke60–80 mm
  • Port sizePT1/8
  • CushionAdjustable, 27 mm
$70.01 $77.51Save 9% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SEJ32 stroke, mounting and version on one page All SEJ32 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SEJ Adjustable Cylinder SEJ32X80-20S

The AirTAC SEJ32X80-20S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 345 N each way at 0.5 MPa. A stop screw on the back rod provides a 20 mm adjustment window, allowing you to dial the retract end position from 60 mm up to the nominal 80 mm stroke.

Because it is an extruded aluminum profile cylinder, it omits external tie rods for a clean exterior. The -S magnet option supports CMSE reed and DMSE electronic sensors for position feedback. Adjustable air cushions at both ends decelerate the load near stroke end, but this mechanical stop is not a locking brake.

Airtac SEJ Adjustable Cylinder SEJ32X80-20S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ32X80-20S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ32 mm
Nominal stroke80 mm
Adjustment window20 mm (60–80 mm)
ConfigurationDouble rod, double acting
Port sizePT1/8
Rod threadM10×1.25
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 27 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø32mm)

PressureForce (both directions)
0.5 MPa346 N
0.7 MPa484 N
Max (@1.0 MPa)70 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ32X80-20S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
32Bore size in mm.
×80Nominal stroke length in mm.
-20Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ32X80-20S Is Used

tune

Press Stroke Calibration

Dial in the exact 60-80 mm end position during machine commissioning, using the 345 N both-way force to test assembly press fits without changing hardware.

swap_horiz

Variable-Stop Conveying

Adjust the retract stop on the fly to handle different package lengths on a sorting line, relying on the equal push and pull forces to move loads smoothly.

science

Lab Positioning Trials

Fine-tune the travel limit for test fixtures, setting the precise end-point mechanically while using DMSE sensors to confirm position.

Is the Airtac SEJ Adjustable Cylinder SEJ32X80-20S the Right Cylinder?

Verify the 20 mm retract window covers your required end-position range before ordering. If your application needs less force, there is no smaller bore in the SEJ range; if you need more, stepping up to the 40 mm bore yields 528 N each way at 0.5 MPa. If the exact end position is fixed and never changes, a standard SED double-rod cylinder is sufficient. This cylinder does not hold position on air loss; for fail-safe holding, use an external rod lock. Ensure your replacement matches the 32 mm bore, 60-80 mm effective stroke, PT1/8 port, and magnet option.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (20mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 20mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ32X80-20S FAQ

The 20 mm window lets you mechanically adjust the retract stroke from a minimum effective stroke of 60 mm up to the nominal 80 mm. You set the position via the back-rod stop screw and lock it in place.

Because it is a double-rod cylinder, the force is identical in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ32X80-20S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SEJ32X80-20S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.