
The AirTAC SEJ Adjustable Cylinder SEJ32X80-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø32mm unit covers an effective stroke of 30–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X80-50 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window, yielding an effective stroke range of 30 to 80 mm. A rod exits both ends, ensuring the annulus area remains identical in both directions. This delivers an equal force of 345 N each way at 0.5 MPa, preventing speed asymmetry.
You dial in the exact retract end-position using a mechanical stop screw on the back rod, then lock it down for repeatable cycles. Built to ISO 15552 dimensions with an extruded aluminum barrel, it omits external tie-rods. It features field-adjustable air cushions at both ends and a standard PT1/8 port. This base SKU ships without a magnet, so it does not support position sensing.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X80-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 50 mm (30–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 50 mm window to set precise 30-80 mm retract stops for placing electronic components of varying heights without changing hardware.
Adjust the retract end-position on the fly to accommodate different carton depths, using the equal 345 N both-way force for stable push and pull.
Fine-tune the exact fluid dispensing height during commissioning, locking the back-rod stop screw once the optimal 30-80 mm drop is found.
Confirm this 50 mm adjustment window covers your positioning range; if you need less micro-adjustment, a fixed-stroke SED saves complexity. For sizing both ways, stepping down is not an option as 32 mm is the smallest bore, but stepping up to the 40 mm bore provides 528 N at 0.5 MPa if your load exceeds the 345 N available here. If your application requires fail-safe position holding on air loss, note that the stop screw and air cushions only set the mechanical end and decelerate the stroke; you will need an external rod lock.
When replacing an ISO 15552 cylinder, match the 80 mm nominal stroke, 50 mm window, PT1/8 port, and your required mounting from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2). Because the stroke is under 300 mm, side-load stress is manageable, but always ensure the external guide absorbs any moment load to protect the 12 mm rod.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 50 mm. This gives an effective stroke range of 30 to 80 mm, allowing you to fine-tune the end position on the machine and lock it in place.
Because it is a double-rod cylinder, force is identical in both directions. It provides 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.