
The AirTAC SEJ Adjustable Cylinder SEJ32X80-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø32mm unit covers an effective stroke of 30–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X80-50S is a double-acting, double-rod ISO 15552 profile cylinder with a 50 mm mechanical stroke-adjustment window, yielding an effective retract range of 30 to 80 mm. A rod exits both ends, meaning the annular area is identical in both directions.
You dial in the exact end position using a stop screw on the back rod, then lock it down—perfect for machine commissioning or matching a stop precisely. The extruded aluminum barrel has no external tie rods, and the included -S magnet supports CMSE reed and DMSE electronic sensors for position feedback. Adjustable air cushions at both ends absorb kinetic energy near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X80-50S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 50 mm (30–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 50 mm window to set a precise 30-80 mm retract for a fluid dispensing probe. The equal 345 N both-way force ensures consistent contact pressure without drift.
Adjust the mechanical stop on the fly when switching between product heights on a small assembly fixture. The double-rod design keeps speed identical in both directions.
Use the back-rod stop screw to find the exact end position during machine commissioning. Once set, lock it down and rely on the adjustable air cushions to decelerate the 12 mm rod smoothly.
Verify the 50 mm adjustment window covers your positioning range; if you need less fine-tune travel, a fixed-stroke SED saves cost, but this SEJ excels at variable-stop applications. For sizing, this 32 mm bore yields 345 N both ways at 0.5 MPa. If that is insufficient, stepping up to the 40 mm bore provides 528 N; conversely, there is no smaller SEJ bore, so 32 mm is your minimum. Remember, the air cushion and back-rod stop screw decelerate the load but do not hold position on air loss—for fail-safe holding, specify an external rod lock.
When replacing an ISO 15552 cylinder, match the 32 mm bore, 80 mm nominal stroke, PT1/8 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). The 12 mm rod and M10x1.25 end thread dictate your mounting interface; ensure external guides absorb side loads, especially as overall length is longer than a single-rod SE due to the rear rod.
Quick checklist
A stop screw on the rear rod mechanically limits the retract stroke. The 50 mm window lets you dial the effective stroke down from 80 mm to 30 mm. You set the exact end position on the machine, then lock the screw.
Because it is a double-rod cylinder, force is equal in both directions. It provides 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.