
The AirTAC SEJ Adjustable Cylinder SEJ32X80-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø32mm unit covers an effective stroke of 5–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X80-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75mm adjustable stroke window, yielding an effective stroke range of 5-80mm. A rod exits both ends, ensuring the annulus area remains identical in both directions. This delivers an equal output force of 345N each way at 0.5MPa.
You dial in the retract end position via a mechanical stop screw on the back rod, then lock it in place during commissioning. Equipped with a standard magnet (-S), it supports CMSE reed and DMSE electronic sensors for position feedback. The extruded aluminum barrel contains no external tie rods, and adjustable air cushions at both ends safely decelerate the 12mm rod near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X80-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 75 mm (5–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 75mm retract window to match varying carton heights on a packaging line, using the 345N both-way force to push flaps without needing new hardware.
Fine-tune the 5-80mm effective stroke during machine commissioning to precisely seat small electronic components, locking the back-rod stop screw once aligned.
Adjust the mechanical end stop on the fly for short-run machined parts, relying on the equal 483N retract and extend force at 0.7MPa for consistent clamping.
Verify that the 75mm adjustment window covers your required end-position range. If you need less fine-tune travel, a fixed-stroke SED double-rod cylinder might suffice. For sizing, this 32mm bore provides 345N both ways at 0.5MPa. Stepping down is not an option as this is the smallest bore, but stepping up to the 40mm bore yields 528N both ways at 0.5MPa if your load requires more force.
This cylinder is dimensionally interchangeable per ISO 15552, so match your replacement by bore, stroke, port PT1/8, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Note that the air cushion and stop screw only set the mechanical end and decelerate the load; they do not hold position on air loss. For fail-safe holding, use an external rod lock.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 75mm. This gives an effective stroke range of 5-80mm, allowing you to fine-tune the end position on the machine without changing cylinder hardware. You lock the screw after setting your desired position.
Because it is a double-rod cylinder, the force is identical in both directions. It provides 345N at 0.5MPa, 483N at 0.7MPa, and a maximum of 70kgf at 1.0MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.