
The AirTAC SEJ Adjustable Cylinder SEJ40X100-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø40mm unit covers an effective stroke of 0–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X100-100S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 100mm adjustable stroke window. A rod exits both ends, yielding an identical annulus area for extension and retraction. This provides equal force in both directions—delivering 528N at 0.5MPa and 739N at 0.7MPa each way. The rear stop screw lets you dial the retract stroke down from 100mm to an effective 0mm.
Because the rod exits both ends, it can carry a cam or flag for position sensing. The integrated -S magnet supports CMSE reed and DMSE electronic sensors. Adjustable air cushions at both ends decelerate the load near stroke end, but this mechanism is not a lock; a plain SEJ will not hold position on air loss.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X100-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 100 mm (0–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the retract stroke from 0 to 100mm to precisely set the packaging flap folding stop, using the 739N both-way force to securely hold the carton during glue application.
Swap the mechanical end position for different machined part heights without rewriting PLC logic, relying on the equal extend and retract forces for consistent 528N clamping.
Sweep through trial positions on a materials test rig by adjusting the back-rod stop screw, locking it after finding the exact 40mm impact point.
This 40mm bore model fits applications needing 528N to 739N of both-way thrust. If your application requires less force, step down to the 32mm bore (345N at 0.5MPa). For heavier drives, step up to the 50mm bore (825N at 0.5MPa). If your end position never varies, a fixed-stroke SED avoids the stop-screw mechanism entirely.
When replacing an ISO 15552 cylinder, match the 100mm nominal stroke, the 0-100mm adjustment window, PT1/4 ports, and your mounting choice from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2—FB, CA, CB, and CR are omitted). The 16mm rod and M12x1.25 thread provide a robust interface for external guides to manage side loads.
Quick checklist
The 100mm adjustment window lets you mechanically dial the retract stroke from an effective 0mm up to the full 100mm nominal stroke using the back-rod stop screw, which you lock after setting the exact end position.
Because the rod exits both ends, force is equal in both directions: 528N at 0.5MPa, 739N at 0.7MPa, and a maximum of 108kgf at 1.0MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.