
The AirTAC SEJ Adjustable Cylinder SEJ40X100-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø40mm unit covers an effective stroke of 90–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X100-10S is a double-acting, double-rod ISO 15552 profile cylinder with a 10 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 528 N each way at 0.5 MPa. You dial the retract end from 90 to 100 mm to hit an exact machine stop.
A mechanical stop screw on the back rod lets you set that fine end-position on the machine, then lock it down without swapping hardware. The extruded aluminum barrel has no external tie rods, and the -S magnet enables position feedback via CMSE reed or DMSE electronic sensors. Adjustable air cushions at both ends decelerate the 16 mm rod near stroke extremes.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X100-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 10 mm (90–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 10 mm retract window to perfectly match drill bit penetration depth on a PCB router, leveraging the equal 528 N both-way force at 0.5 MPa for consistent plunging.
Adjust the 90 to 100 mm end position on the fly when switching carton sizes on a packaging line, using the 739 N retract force to positively push the mechanical stop.
Fine-tune the exact open height of a metering valve during commissioning, locking the back-rod stop screw once the precise fluid drop volume is achieved.
Verify the 10 mm window covers your positioning tolerance, giving a 90 to 100 mm effective range. If you need less force, the adjacent bore 32 drops to 345 N at 0.5 MPa; if you need more, stepping up to bore 50 provides 825 N at 0.5 MPa. If your end position never changes, a fixed-stroke SED avoids the adjustment mechanism.
For a fail-safe hold on air loss, add an external rod lock, as the cushion and stop screw only set the mechanical end and decelerate. To match this ISO 15552 cylinder for a direct replacement, confirm the 100 mm nominal stroke, PT1/4 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 10 mm window. This means your effective stroke range is 90 to 100 mm, allowing you to fine-tune the end position on the machine and lock it in without changing the cylinder hardware.
Because it is a double-rod cylinder, the force is equal in both directions. It provides 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.