
The AirTAC SEJ Adjustable Cylinder SEJ40X100-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø40mm unit covers an effective stroke of 80–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X100-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force is perfectly equal in both directions at 528 N each way at 0.5 MPa. The integrated -S magnet enables position detection with CMSE reed or DMSE electronic sensors.
A mechanical stop screw on the back rod lets you dial the retract end over a 20mm window, providing an effective stroke range of 80 to 100 mm. This allows precise end-position tuning directly on the machine. The extruded aluminum barrel omits external tie rods, and field-adjustable air cushions at both ends decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X100-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 20 mm (80–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Fine-tune a 90mm retract stop to match varying package heights on a packaging line, using the 528 N both-way force to halt boxes securely.
Dial the end position during product changeovers to insert locating pins into different jig heights without swapping hardware.
Trial position a 100mm stroke press for bearing seating, adjusting the final 20mm to find the exact contact depth before locking.
Confirm the 20mm adjustment window covers your positioning needs, allowing an effective 80 to 100mm stroke. If sizing force, the neighboring bore down (32mm) yields 345 N each way at 0.5 MPa, while stepping up to the 50mm bore provides 825 N each way. If you do not require variable end-position tuning, a fixed-stroke SED cylinder is sufficient. The plain SEJ does not hold position on air loss; the cushion and stop screw only set the mechanical end, so specify an external rod lock for fail-safe holding.
As a dimensionally interchangeable ISO 15552 cylinder, match your existing bore, stroke, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2) for a direct replacement. The 16mm rod and M12x1.25 thread handle standard axial loads, though external guides are recommended for any lateral forces.
Quick checklist
A stop screw on the back rod lets you mechanically shorten the retract stroke over a 20mm window. The effective stroke is 80 to 100mm. You dial the end position to match your machine, then lock it.
Because it is a double-rod cylinder, force is equal both ways: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.