verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ40X100-30S

The AirTAC SEJ Adjustable Cylinder SEJ40X100-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø40mm unit covers an effective stroke of 70–100mm without changing cylinders. Force is equal in both directions.

  • BoreØ40 mm
  • Nominal stroke100 mm
  • Adjust window30 mm
  • Effective stroke70–100 mm
  • Port sizePT1/4
  • CushionAdjustable, 30 mm
$78.39 $85.89Save 8% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SEJ40 stroke, mounting and version on one page All SEJ40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SEJ Adjustable Cylinder SEJ40X100-30S

The AirTAC SEJ40X100-30S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 30 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force stays equal in both directions at 528 N each way at 0.5 MPa. The retract end uses a mechanical stop screw on the back rod, letting you dial the effective stroke down from 100 mm to 70 mm for exact machine commissioning.

This bore 40 unit runs on PT1/4 ports with a Ø16 mm rod and M12x1.25 rod-end thread. The extruded aluminum barrel omits external tie rods for a clean ISO 15552 profile. Equipped with a standard magnet, it supports CMSE reed and DMSE electronic sensors for position feedback. Adjustable air cushions at both ends decelerate the load near stroke end.

Airtac SEJ Adjustable Cylinder SEJ40X100-30S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ40X100-30S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ40 mm
Nominal stroke100 mm
Adjustment window30 mm (70–100 mm)
ConfigurationDouble rod, double acting
Port sizePT1/4
Rod threadM12×1.25
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressureForce (both directions)
0.5 MPa528 N
0.7 MPa739 N
Max (@1.0 MPa)108 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ40X100-30S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
40Bore size in mm.
×100Nominal stroke length in mm.
-30Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ40X100-30S Is Used

tune

Press Stroke Calibration

Dial the 30 mm retract window to set a precise 70-100 mm pressing depth for 528 N assembly force without swapping hardware.

swap_horiz

Part Height Changeover

Adjust the back-rod stop screw on the fly to accommodate varying product heights on a packaging line, maintaining equal force both ways.

precision_manufacturing

Sensor Flag Tracking

Use the extending rear rod to carry a cam for DMSE electronic sensors while adjusting the end position to trial-fit components.

Is the Airtac SEJ Adjustable Cylinder SEJ40X100-30S the Right Cylinder?

Verify the 30 mm adjustment window covers your positioning range, allowing you to fine-tune the retract end from 70 mm up to 100 mm. If 528 N at 0.5 MPa is excessive, step down to the 32 mm bore offering 345 N both ways. If you need more push, the 50 mm bore provides 825 N. If your travel never varies, a fixed-stroke SED saves cost and length. Remember this cylinder does not hold position on air loss; the cushion and stop screw only set the mechanical end and decelerate, so specify an external rod lock for fail-safe holding. At 100 mm stroke, side-load is minimal, but always guide external loads to protect the rod seals. Match your ISO 15552 replacement by verifying bore, port PT1/4, and mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (30mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 30mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ40X100-30S FAQ

A stop screw on the rear rod mechanically shortens the retract stroke. For this SEJ40X100-30S, you can dial the effective stroke anywhere from 70 mm up to the nominal 100 mm. You lock the screw after setting your desired end position.

Because it is a double-rod cylinder, force is equal both ways: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ40X100-30S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SEJ40X100-30S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.