
The AirTAC SEJ Adjustable Cylinder SEJ40X125-100 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø40mm unit covers an effective stroke of 25–125mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X125-100 is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so that drive force is equal in both directions at 528 N at 0.5 MPa. The retract end uses a mechanical stop screw on the back rod to provide a 100 mm adjustment window, allowing you to dial the effective stroke anywhere from 25 mm up to 125 mm without changing mounting hardware.
This bore 40 mm actuator features a PT1/4 port, a 16 mm rod with an M12x1.25 thread, and field-adjustable air cushions at both ends to manage deceleration. Because it is an extruded aluminum profile cylinder, it offers true ISO 15552 dimensional interchangeability without any external tie rods. This specific SKU lacks a piston magnet, so it will not support CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X125-100 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 125 mm |
| Adjustment window | 100 mm (25–125 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×125 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 25 to 125 mm insertion depth for pressing bearings into housings, utilizing the 528 N both-way force and the 100 mm stop-screw window to perfect the end position during commissioning.
Fine-tune the mechanical end-stop for a grinding head or deburring tool, locking the back-rod stop screw precisely after positioning to guarantee repeatable travel.
Verify the 100 mm adjustment window comfortably covers your required end-position range; here you can tune the retract stop down to a 25 mm effective stroke for commissioning or part-height changeovers. If you need less force, the next bore down (32 mm) provides 345 N both ways at 0.5 MPa; if your load requires more thrust, stepping up to the 63 mm bore yields 1402 N at 0.5 MPa. If the stroke never needs to change after setup, a fixed-stroke SED cylinder is a simpler alternative. Remember that the adjustable air cushion only decelerates the load near stroke end and does not hold position on air loss; for fail-safe holding, use an external rod lock or a BSED series cylinder. When replacing an ISO 15552 actuator, match the 40 mm bore, 125 mm nominal stroke, PT1/4 port, and your chosen mounting from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The 100 mm adjustment window allows you to mechanically shorten the retract stroke using a stop screw on the back rod. The effective stroke can be dialed anywhere from 25 mm up to the full 125 mm, which is ideal for fine-tuning end positions on the machine without replacing the cylinder.
Because it is a double-rod cylinder, the output force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa. It is an ISO 15552 / VDMA 24562 profile cylinder, meaning it is dimensionally interchangeable per ISO standards and features a PT1/4 port.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.