
The AirTAC SEJ Adjustable Cylinder SEJ40X125-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø40mm unit covers an effective stroke of 75–125mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X125-50 is a double-acting, double-rod ISO 15552 profile cylinder with a 50 mm mechanical stroke adjustment window, yielding an effective retract range of 75 to 125 mm. You dial in the exact end position using a stop screw on the back rod, then lock it down.
This bore features a PT1/4 port, a 16 mm rod with an M12x1.25 end thread, and field-adjustable air cushions at both ends to decelerate the load near stroke termination. The extruded aluminum barrel is dimensionally interchangeable per ISO 15552 standards. Note this specific SKU lacks a piston magnet, so it will not trigger CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X125-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 125 mm |
| Adjustment window | 50 mm (75–125 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×125 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 75-125 mm retract window to hit a precise Z-height on adhesive dispensing probes, leveraging the equal 528 N both-way force to lift the head cleanly without sag.
Quickly reset the mechanical stop for different carton flap heights during format changeovers, using the back-rod screw to set the exact 75 to 125 mm stroke without swapping hardware.
Verify the 50 mm adjustment window safely covers your required end-position variance. If you need less fine-tuning range, dropping to a 32 mm bore yields 345 N both ways at 0.5 MPa, while stepping up to a 63 mm bore provides 1402 N. If your travel distance never changes, a fixed-stroke SED avoids the extra length of the back rod. Remember that the adjustable cushion and stop screw decelerate the load but do not hold position on air loss; a BSED or external rod lock is required for fail-safe holding.
When replacing an ISO 15552 cylinder, match the 40 mm bore, 125 mm nominal stroke, PT1/4 port, and your mounting choice from the SEJ subset (Basic, FA, LB, TC, FTC, TCM1, TCM2). The 125 mm stroke is short enough that side-load stress is minimal, but always ensure the external guides carry the primary radial load.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 50 mm. The effective stroke range is 75 to 125 mm. You set the exact end position on the machine and lock the screw in place.
Because it is a double-rod cylinder, the force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.