
The AirTAC SEJ Adjustable Cylinder SEJ40X125-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø40mm unit covers an effective stroke of 50–125mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X125-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm mechanical adjustment window. This yields an effective retract stroke range of 50-125 mm, allowing you to dial in the exact end position during machine commissioning without swapping hardware.
This bore 40 unit features a PT1/4 port, a Ø16 mm rod with an M12x1.25 thread, and 30 mm adjustable air cushions at both ends to decelerate the load near stroke end. The included -S magnet enables position detection with CMSE reed or DMSE electronic sensors. An extruded aluminum barrel provides ISO 15552 dimensional interchangeability with no external tie rods.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X125-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 125 mm |
| Adjustment window | 75 mm (50–125 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×125 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Micro-adjust the 50-125 mm effective stroke on an assembly fixture to set precise bearing insertion depth.
Reposition a double-rod sorting gate by 50 mm to handle varying product widths on a packaging line.
Confirm this 75 mm adjustment window covers your required positioning range. If you need less fine-tune travel, a smaller window or a fixed-stroke SED saves cost. For sizing, the next bore down (32 mm) yields 345 N both ways at 0.5 MPa, while stepping up to a 63 mm cylinder provides 1402 N. At 125 mm nominal stroke, side loads are moderate, but ensure your external guides accommodate the longer overall length of the double-rod design.
The rear stop screw sets the mechanical end position but does not hold the load on air loss; for fail-safe clamping, specify a BSED or an external rod lock. Ensure your ISO 15552 replacement matches the PT1/4 port, magnet option, and the available mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The rear stop screw provides a 75 mm adjustment window. The effective retract stroke can be mechanically dialed from 50 mm up to the full 125 mm nominal stroke, which is locked in place after setting your end position.
Because the rod exits both ends, force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.