
The AirTAC SEJ Adjustable Cylinder SEJ40X140-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø40mm unit covers an effective stroke of 90–140mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X140-50S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window. A rod exits both ends, yielding an identical annular area so the drive force is perfectly equal extend and retract: 528 N each way at 0.5 MPa. You turn a stop screw on the back rod to mechanically shorten the retract end, giving an effective stroke range of 90-140 mm without changing hardware.
Because it is a profile cylinder, the extruded aluminum barrel carries no external tie rods. The -S magnet enables CMSE reed and DMSE electronic position sensing. Adjustable air cushions at both ends decelerate the load near the stroke ends, and the PT1/4 ports pair with the Ø16 mm rod and M12x1.25 thread.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X140-50S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 140 mm |
| Adjustment window | 50 mm (90–140 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×140 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 50 mm retract window to perfectly position a flight stop on a packaging conveyor, using the 739 N both-way force to push cartons without rod deflection.
Adjust the effective stroke from 90 to 140 mm to accept different part heights on a transfer line, avoiding the need to swap out the entire cylinder.
Fine-tune the end position during a stamping die trial, relying on the double-rod design to keep the platen parallel under the 528 N load at 0.5 MPa.
Confirm this 50 mm adjustment window covers your machine's fine-tuning range; if you need less commissioning play, a fixed-stroke SED saves cost. For sizing both ways: stepping down to bore 32 drops the both-way force to 345 N at 0.5 MPa, while stepping up to bore 50 raises it to 825 N. A plain SEJ does not hold position on air loss; the cushion and stop screw only set the mechanical end and decelerate near stroke end. For fail-safe holding, point to a BSED or an external rod lock. Match ISO 15552 replacements by verifying the 140 mm stroke, 50 mm window, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
A stop screw on the back rod mechanically shortens the retract end. For the SEJ40X140-50S, the 50 mm window lets you dial the effective stroke anywhere from 90 mm up to 140 mm. You lock the screw after setting your exact end position.
Because the double-rod design gives an identical annular area both ways, force is equal extend and retract: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.