
The AirTAC SEJ Adjustable Cylinder SEJ40X150-100 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø40mm unit covers an effective stroke of 50–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X150-100 is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 528 N each way at 0.5 MPa. The retract stroke is mechanically adjustable via a back-rod stop screw over a 100 mm window, giving an effective stroke range of 50 to 150 mm.
This bore 40 unit features a PT1/4 port, a 16 mm rod with an M12x1.25 thread, and field-adjustable air cushions at both ends to decelerate the payload near the end of travel. This SKU ships without a magnet, so it does not support CMSE or DMSE position sensors. The stop screw sets the mechanical end position but does not hold the load on air loss.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X150-100 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 100 mm (50–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 50-150 mm clamping depth on a pneumatic press. The 528 N both-way force at 0.5 MPa is sufficient for light assembly tasks while the stop screw locks the precise end position.
Accommodate varying carton sizes on a packaging line. Adjust the retract end up to 100 mm to match new flap heights without replacing the cylinder or redesigning the mounting plate.
Find the optimal engagement depth for a 16 mm rod during prototyping. Set the mechanical end precisely, then lock the stop screw once the 739 N both-way force at 0.7 MPa correctly seats the part.
Verify the 100 mm adjustment window covers your required end-position range, allowing you to fine-tune the 50 to 150 mm effective stroke directly on the machine without swapping hardware. For sizing, if you need less force, step down to the bore 32 model which provides 345 N both ways at 0.5 MPa; if you need more thrust, step up to the bore 50 model which provides 825 N both ways at 0.5 MPa. If your application never requires stroke changes, a fixed-stroke SED cylinder is a simpler alternative. For fail-safe load holding on air loss, use an external rod lock or BSED. This cylinder is dimensionally interchangeable per ISO 15552, so match the bore, stroke, port, and mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) for direct replacement.
Quick checklist
The retract end features a stop screw on the back rod that allows you to shorten the stroke over a 100 mm window. The effective stroke range is 50 to 150 mm, which you can fine-tune directly on the machine and lock in place.
Because a rod exits both ends, the force is identical in both directions. It provides 528 N each way at 0.5 MPa, 739 N each way at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.