
The AirTAC SE40 Standard Cylinder SE40X150 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 150mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X150 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for seamless retrofitting.
This 40 mm bore unit features a 16 mm hard-chrome rod with an M12x1.25 thread, achieving a balanced 528 N pull force. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed 30-800 mm/s cycling. Note that this specific SKU lacks a built-in magnet, so it does not directly support CMSE or DMSE position sensing without modification.
| Model | Airtac SE40 Standard Cylinder SE40X150 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 628 N push force needed to reliably fold and seal corrugated carton flaps on high-speed packaging lines operating at 30-800 mm/s.
Actuates routing gates on modular conveyor systems, utilizing the 150 mm stroke to redirect pallets smoothly without external tie-rod interference.
Acts as a positive mechanical stop for secondary drilling operations, where the field-adjustable cushion gently decelerates the tool carriage at stroke end.
When sizing this actuator, compare its 628 N push at 0.5 MPa against the neighboring bores: step down to a 32 mm bore for lighter 402 N loads, or move up to a 50 mm bore if your application requires 982 N of extension force. Because this is a standard double-acting cylinder, it will not hold a load if air pressure is lost or the valve is centered; use a BSE rod lock variant for fail-safe positioning. For direct replacements, match the 40 mm bore, 150 mm stroke, PT1/4 port, and your required mounting accessory. The 150 mm stroke is well within standard bearing limits, but if you push beyond 300 mm, always add an external guide to prevent rod-bearing bending under side loads.
Quick checklist
The SE40X150 generates 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum of 128 kgf at 1.0 MPa. It uses a PT1/4 port and features a 16 mm rod with an M12x1.25 thread.
Yes, the SE40X150 is dimensionally interchangeable with any ISO 15552 / VDMA 24562 cylinder, meaning it shares identical mounting footprint and accessory compatibility. However, this specific SKU lacks the -S magnet, so it cannot support CMSE or DMSE sensors without modification.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.