
The AirTAC SEJ Adjustable Cylinder SEJ40X150-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø40mm unit covers an effective stroke of 50–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X150-100S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 100mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force is exactly equal in both directions at 528 N each way at 0.5 MPa. By turning the stop screw on the back rod, you mechanically set the retract end position, giving an effective stroke range of 50 to 150 mm.
This 40mm bore utilizes a PT1/4 port, a 16mm rod with an M12x1.25 thread, and adjustable air cushions at both ends to manage deceleration. The built-in -S magnet supports CMSE reed and DMSE electronic sensors for position feedback. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X150-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 100 mm (50–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 50-150mm clamping depth on a small pneumatic press without swapping hardware, using the 528N both-way force to secure light sheet metal.
Adjust the retract stop to match varying cardboard box heights during format changeovers, relying on the 100mm window for rapid mechanical setup.
Set a precise trial end-position for drilling or pin-insertion heads, fine-tuning the stroke on the machine until the 739N at 0.7 MPa hits the exact target.
Verify the 100mm adjustment window covers your required end-position; here you can dial the retract stroke anywhere from 50mm up to the full 150mm. If you need less force, the adjacent 32mm bore provides 345 N at 0.5 MPa; if you need more, step up to the 50mm bore which provides 825 N at 0.5 MPa. If your machine never requires stroke tuning, a fixed-stroke SED cylinder is sufficient. Note that the adjustable cushion and stop screw only set the mechanical end and decelerate near stroke end; a plain SEJ does not hold position on air loss, so use an external rod lock for fail-safe hold. For ISO 15552 replacement matches, confirm the 40mm bore, 150mm stroke, PT port, and desired mounting kit.
Quick checklist
The 100mm window allows you to dial the retract end position from an effective stroke of 50mm up to the nominal 150mm. You set the stop screw on the back rod and lock it after positioning.
Because the rod exits both ends, force is equal in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.