
The AirTAC SEJ Adjustable Cylinder SEJ40X150-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø40mm unit covers an effective stroke of 110–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X150-40S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 528 N each way at 0.5 MPa. The retract end is mechanically adjustable via a back-rod stop screw, providing a 40 mm dial-in window for an effective stroke range of 110-150 mm.
This configuration includes a magnet for position sensing, supporting CMSE reed and DMSE electronic switches. It features field-adjustable air cushions at both ends to decelerate the load near the stroke ends and uses a PT1/4 port with a Ø16 mm rod. The mounting set omits FB, CA, CB, and CR options, focusing on Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X150-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 40 mm (110–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 110-150 mm retract position for different material thicknesses on a stamping press, using the 528 N both-way force to consistently actuate the stripper plate.
Adjust the mechanical stop screw on the fly when switching carton sizes on a packaging line, avoiding hardware changes while maintaining equal push and pull force.
Fine-tune the clamping end position during robotic welding commissioning, using the adjustable stroke to match part tolerances precisely without reprogramming the PLC.
Confirm the 40 mm adjustment window covers your required end-position variance, letting you dial in the retract stop from 110 to 150 mm during commissioning without swapping hardware. If you need less force, the adjacent 32 mm bore provides 345 N both ways at 0.5 MPa; if your load is heavier, step up to the 50 mm bore for 825 N both ways. A fixed-stroke SED cylinder is sufficient if you do not need to fine-tune the end stop on the machine.
For any stroke at or above 300 mm, external guides are recommended to prevent rod side-load damage. A plain SEJ cylinder does not hold position on air loss; the adjustable cushion and stop screw only set the mechanical end and decelerate near stroke end, not act as a fail-safe lock. To match this ISO 15552 replacement, verify your bore, stroke, 40 mm window, PT port, and magnet requirements.
Quick checklist
The retract stroke has a 40 mm adjustment window. You can mechanically dial the effective stroke down from the nominal 150 mm to 110 mm using the back-rod stop screw, then lock it in place.
Because the rod exits both ends, the force is equal in both directions. It provides 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.