
The AirTAC SEJ Adjustable Cylinder SEJ40X150-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø40mm unit covers an effective stroke of 100–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X150-50 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window. A rod exits both ends, yielding an annulus area that generates identical force in both directions—delivering 528 N each way at 0.5 MPa. The effective stroke range spans 100 to 150 mm.
A mechanical stop screw on the back rod lets you dial in the exact retract end-position during machine commissioning. You must lock the screw after setting your target dimension. This cylinder has no magnet, so it will not support CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X150-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 50 mm (100–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 100-150mm clamping depth on a small pneumatic press, using the 528N both-way force to seat bearings without over-traveling.
Adjust the retract stop to match varying cardboard flap heights, fine-tuning the stroke window on the fly during product format changes.
Iteratively test the end-stop for a drilling fixture, locking the back-rod screw precisely when the 40mm bore achieves the target alignment.
Verify the 50 mm adjustment window covers your required positioning range. If you need less fine-tune travel, the SEJ40X150-20 offers a 20 mm window. For higher force, the 50 mm bore provides 825 N both ways at 0.5 MPa; for lighter loads, the 32 mm bore yields 345 N. If your end-position never changes, a fixed-stroke SED cylinder is sufficient.
This SKU lacks a magnet, meaning no electronic or reed feedback. The adjustable air cushion at both ends decelerates the piston near the end of travel but does not hold position on air loss; for fail-safe holding, use an external rod lock or BSED. It uses a PT1/4 port and M12x1.25 rod thread.
Quick checklist
The 50 mm adjustment window allows you to shorten the retract stroke from the nominal 150 mm down to 100 mm. You set the exact end-position using the back-rod stop screw and lock it in place.
Because the rod exits both ends, force is equal in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.