
The AirTAC SEJ Adjustable Cylinder SEJ40X150-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø40mm unit covers an effective stroke of 75–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X150-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75mm adjustable stroke window, allowing you to dial the retract end from 75mm up to 150mm. A rod exits both ends, creating identical annulus areas so the output force is equal in both directions at 528 N each way at 0.5 MPa.
The retract position is set via a mechanical stop screw on the back rod, which you lock down after finding the exact end point. It includes a magnet for CMSE reed or DMSE electronic sensors, and uses field-adjustable air cushions at both ends to decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X150-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 75 mm (75–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 75mm retract window to match varying carton heights on the fly, using the 528N both-way force to cleanly fold flaps without crushing the board.
Fine-tune the pressing depth of a 150mm stroke pin insertion actuator during commissioning, locking the back-rod stop once the exact 75-150mm contact point is found.
Verify the 75mm adjustment window covers your required retract range. If you need less force, the 32mm bore provides 345 N both ways at 0.5 MPa; if your load is heavier, step up to the 50mm bore which provides 825 N both ways. If your end position never changes, a fixed-stroke SED cylinder is sufficient. For a direct ISO 15552 replacement, match the 40mm bore, 150mm stroke, PT1/4 port, and mounting style (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Since this is a 150mm stroke, external guides are recommended to prevent side-load wear on the 16mm rod. Note that the stop screw and air cushions only set the mechanical end and decelerate the load; they do not hold position on air loss, so use an external rod lock for fail-safe holding.
Quick checklist
The 75mm adjustment window allows you to mechanically shorten the retract stroke from the nominal 150mm down to 75mm. You set the exact end position using a stop screw on the back rod and lock it in place.
Because the rod exits both ends, the force is identical in both directions. It provides 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.