
The AirTAC SEJ Adjustable Cylinder SEJ40X160-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø40mm unit covers an effective stroke of 120–160mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X160-40S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 40 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force stays equal in both directions at 528 N each way at 0.5 MPa. The retract end uses a mechanical stop screw on the back rod, letting you dial the effective stroke down from 160 mm to 120 mm for precise on-machine positioning.
Because it carries the S suffix, this unit includes a magnet for CMSE reed or DMSE electronic position sensing. The extruded aluminum barrel has no external tie rods, accepts adjustable air cushions at both ends to manage kinetic energy, and uses a PT1/4 port with a 16 mm rod. Lock the stop screw firmly after setting your end position to prevent drift.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X160-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 160 mm |
| Adjustment window | 40 mm (120–160 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×160 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 40 mm retract window to perfectly match varying part widths on an automated lathe, using the 739 N at 0.7 MPa to securely clamp without retooling.
Adjust the effective stroke between 120 and 160 mm on a carton flap folder, relying on the equal both-way force for crisp folding and return.
Fine-tune electrode approach distance during prototype runs, locking the back-rod stop screw once the exact contact point is found.
Verify the 40 mm adjustment window covers your required positioning range, giving an effective 120-160 mm stroke. If you need less force, stepping down to the 32 mm bore drops output to 345 N at 0.5 MPa; if your load is heavier, stepping up to the 50 mm bore raises it to 825 N. If you never need to alter the end position after commissioning, a fixed-stroke SED saves complexity. Remember the air cushion and stop screw only decelerate and set the mechanical end; they do not hold position on air loss, so specify an external rod lock for fail-safe holding. Mounting options are limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 40 mm window. The effective stroke can be dialed from 160 mm down to 120 mm, allowing precise end-position tuning directly on the machine.
Because it is a double-rod cylinder, the force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.