
The AirTAC SEJ Adjustable Cylinder SEJ40X175-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø40mm unit covers an effective stroke of 75–175mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X175-100S is a double-acting, double-rod ISO 15552 profile cylinder with a 100 mm mechanical stroke-adjustment window. You can dial the retract end from 75 mm up to the 175 mm nominal stroke to perfectly match a machine stop or part height during commissioning. A rod exits both ends, yielding identical extend and retract annulus areas for equal force—528 N each way at 0.5 MPa and 739 N at 0.7 MPa.
The extruded aluminum barrel contains no external tie rods, ensuring clean, dimensionally interchangeable ISO 15552 mounting. It includes an -S magnet for CMSE reed or DMSE electronic sensors and field-adjustable air cushions at both ends to decelerate the load near stroke end. The back-rod stop screw sets the mechanical end position; lock it after setting, as the cushion is not a fail-safe brake.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X175-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 175 mm |
| Adjustment window | 100 mm (75–175 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×175 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 100 mm retract window to match varying carton heights on the fly, using the equal 528 N both-way force to consistently tuck flaps without crushing the box.
Fine-tune the 75-175 mm end position against a hard stop during CNC changeovers, locking the back-rod screw precisely where the 739 N @0.7 MPa clamping force is needed.
Adjust the stroke on the machine to press bearings to exact depths across different housings, relying on the twin-rod design for stable, non-rotating pressing.
Confirm this 100 mm window covers your required positioning range. If you need less fine-tune travel, a fixed-stroke SED saves cost. For sizing both ways: stepping down to a 32 mm bore yields 345 N both ways at 0.5 MPa, while stepping up to a 50 mm bore provides 825 N. This 40 mm bore delivers 528 N at 0.5 MPa (108 kgf max at 1.0 MPa) and runs at 30-800 mm/s. Match your ISO 15552 replacement by verifying the PT1/4 port, M12x1.25 rod thread, and mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2. For this 175 mm stroke, ensure external guides support side loads to prevent rod binding.
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke over a 100 mm window. Your effective stroke range is 75 mm to 175 mm. You set the exact end position on the machine, then lock the screw; it is not a pneumatic position lock.
Because it is a double-rod cylinder, the force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.