
The AirTAC SE40 Standard Cylinder SE40X175 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 175mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X175 is a double-acting, single-rod ISO 15552 profile cylinder engineered for industrial pneumatics. Delivering 628 N of push force at 0.5 MPa and 879 N at 0.7 MPa, it fits neatly into mid-range actuation tasks. The extruded aluminum barrel design omits external tie rods entirely, yielding a compact, corrosion-resistant body that mounts flush against machinery frames without protruding hardware.
Unlike fixed rubber bumpers, this actuator features a field-adjustable pneumatic cushion at both ends, allowing technicians to dial in end-of-stroke deceleration via a set screw to prevent hard impacts during high-speed cycling. This specific SKU lacks a built-in position magnet, so it operates without electronic or reed sensor feedback out of the box.
| Model | Airtac SE40 Standard Cylinder SE40X175 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 175 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
With 628 N of push at 0.5 MPa and a 175 mm stroke, this cylinder reliably gates corrugated cartons between parallel conveyor belts in continuous-flow packaging lines.
The 40 mm bore generates sufficient clamping force to hold aluminum castings in a CNC milling vise, while the adjustable cushion softens retraction at 800 mm/s.
A compact 175 mm stroke pushes processed test tubes out of a centrifuge carousel, utilizing the clean profile barrel for easy washdown in lab environments.
When sizing this 40 mm bore actuator, evaluate your actual thrust requirements: stepping down to a 32 mm bore yields 402 N of push at 0.5 MPa, while moving up to a 50 mm bore provides 982 N. At 175 mm of stroke, the 16 mm rod and M12x1.25 thread handle moderate side loads, but for any unsupported length over 300 mm you should add an external guide to prevent rod-bearing bending. As a true ISO 15552 profile cylinder, it serves as a direct dimensional replacement for other standard VDMA 24562 actuators sharing the PT1/4 port and 175 mm stroke. Remember that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure drops—use a BSE rod lock for fail-safe positioning.
Quick checklist
The SE40X175 delivers 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, with a maximum push force of 128 kgf at 1.0 MPa. It operates at a speed range of 30-800 mm/s.
No, this specific SE40X175 SKU is manufactured without a built-in piston magnet (-S option). To use CMSE reed or DMSE electronic position sensors, you must select an SE model designated with the 'S' suffix.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.