
The AirTAC SEJ Adjustable Cylinder SEJ40X175-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø40mm unit covers an effective stroke of 155–175mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X175-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window, yielding an effective travel range of 155 to 175mm. A rod exits both ends, ensuring the annulus area remains identical in both directions. This delivers an equal output force of 528N at 0.5MPa and 739N at 0.7MPa each way.
You dial in the exact retract end-position using a mechanical stop screw on the back rod, then lock it down for precise machine commissioning. The extruded aluminum barrel contains no external tie rods, and the included -S magnet enables position detection with CMSE reed or DMSE electronic sensors. Field-adjustable air cushions at both ends absorb kinetic energy near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X175-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 175 mm |
| Adjustment window | 20 mm (155–175 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×175 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Fine-tune the 155-175mm retract stop on a coil feed line to hit exact material lengths, utilizing the 528N both-way force to push and pull the gauge consistently.
Quickly adjust the stroke window when switching a carton erector to different box depths, letting the double-rod equal thrust push flaps without re-mounting hardware.
Trial position a 739N pressing assembly against delicate electronic connectors, using the back-rod stop screw to set a precise, non-destructive mechanical end.
Verify the 20mm adjustment window covers your required end-position variance, providing that 155-175mm effective range. For lower force requirements, stepping down to the 32mm bore yields 345N at 0.5MPa; if you need more thrust, stepping up to the 50mm bore provides 825N at 0.5MPa. If your application never requires end-position tuning, a fixed-stroke SED cylinder is sufficient. For replacing an ISO 15552 unit, match the 40mm bore, 175mm nominal stroke, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Note that the air cushion and stop screw decelerate the load but do not hold position on air loss; fail-safe holding requires an external rod lock. At 175mm stroke, ensure external guides manage side loads to protect the 16mm rod.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 20mm. For a 175mm nominal stroke, the effective travel range becomes 155 to 175mm, which you lock in place after fine-tuning the machine end-position.
Because it is a double-rod cylinder, the force is identical in both directions: 528N at 0.5MPa, 739N at 0.7MPa, and a maximum of 108kgf at 1.0MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.