
The AirTAC SEJ Adjustable Cylinder SEJ40X175-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø40mm unit covers an effective stroke of 145–175mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X175-30S is a double-acting, double-rod ISO 15552 profile cylinder with a 30 mm adjustable stroke window, yielding an effective travel range of 145 to 175 mm. A rod exits both ends, meaning the annulus area is identical in both directions. This provides an equal drive force of 528 N each way at 0.5 MPa, eliminating speed discrepancies between extend and retract.
You dial in the exact retract end-position using a mechanical stop screw on the back rod, then lock it in place. This unit includes a magnet (-S) for CMSE reed or DMSE electronic sensors. The extruded aluminum barrel has no external tie rods, and adjustable air cushions at both ends decelerate the 16 mm rod near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X175-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 175 mm |
| Adjustment window | 30 mm (145–175 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×175 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 30 mm retract window to match varying part heights during press changeovers. The equal 528 N both-way force ensures consistent clamping without retract speed loss.
Fine-tune the 145-175 mm stroke range on a conveyor diverter gate to route different package sizes precisely without swapping hardware.
Commission a fluid dispenser by adjusting the back-rod stop screw to dial the exact shot volume, relying on the 16 mm rod for stable mechanical positioning.
Verify the 30 mm adjustment window covers your machine's positioning range. If you need less force, stepping down to the 32 mm bore yields 345 N both ways at 0.5 MPa; if you need more thrust, the 50 mm bore provides 825 N. If the end-position never changes after commissioning, a fixed-stroke SED is sufficient. Note that the air cushion and stop screw decelerate the load but do not hold position on air loss; for fail-safe holding, use an external rod lock. For a true ISO 15552 replacement, match the 175 mm stroke, PT1/4 port, and mounting style (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 30 mm. For this 175 mm model, the effective stroke range is 145 to 175 mm. You set the exact end-position on the machine, then lock the screw.
Because it is a double-rod cylinder, force is equal in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.