
The AirTAC SEJ Adjustable Cylinder SEJ40X175-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø40mm unit covers an effective stroke of 125–175mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X175-50 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window. By turning the mechanical stop screw on the back rod, you can dial the retract end-position down, giving an effective stroke range of 125 to 175 mm without changing hardware.
This unit uses an extruded aluminum barrel with no external tie rods and includes field-adjustable air cushions at both ends to decelerate the load near stroke end. It features a 16 mm rod, M12x1.25 rod-end thread, and PT1/4 ports. This specific SKU lacks the -S magnet option, so it does not support CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X175-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 175 mm |
| Adjustment window | 50 mm (125–175 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×175 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 125 to 175 mm retract stop during machine commissioning, using the back-rod screw to perfectly match a varying end-position without swapping cylinders.
Apply the equal 528 N both-way force to push and pull a light machining fixture, rapidly adjusting the stroke when switching the line to different part heights.
Use the double-rod design to resist side load and guide a spotting drill, fine-tuning the 50 mm window to find the optimal contact depth before locking the screw.
Confirm the 50 mm adjustment window covers your required positioning range; here you can fine-tune the retract stroke anywhere from 125 mm up to the full 175 mm. If you need less force, step down to the 32 mm bore (345 N both ways at 0.5 MPa); if pushing heavier loads, step up to the 50 mm bore (825 N both ways). If your end-position never varies, a fixed-stroke SED cylinder is sufficient. For fail-safe load holding on air loss, note that this cylinder does not hold position—use a BSED or an external rod lock. When replacing an ISO 15552 unit, match the 40 mm bore, 175 mm stroke, 50 mm window, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 50 mm window. You can set the effective stroke anywhere from 125 mm up to 175 mm, then lock the screw in place.
Because it is a double-rod cylinder, the force is equal in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.