
The AirTAC SEJ Adjustable Cylinder SEJ40X200-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø40mm unit covers an effective stroke of 160–200mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X200-40S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 40 mm adjustable stroke window. A rod exits both ends, yielding equal force in both directions—delivering 528 N each way at 0.5 MPa. You can dial the retract end from 160 mm up to the 200 mm nominal stroke, allowing precise on-machine end-position tuning without changing hardware.
This bore uses a PT1/4 port and a Ø16 mm rod with an M12x1.25 thread. The extruded aluminum barrel contains no external tie rods, and the field-adjustable air cushion at both ends decelerates the load near stroke end. Equipped with a standard magnet, it supports CMSE reed and DMSE electronic sensors for position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X200-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 200 mm |
| Adjustment window | 40 mm (160–200 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×200 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 40 mm retract window to hit a precise stop on a coil feed line. The 739 N both-way force at 0.7 MPa securely pushes the material guide without asymmetric drift.
Switch between different carton heights by adjusting the effective stroke from 160 to 200 mm on the fly. The double-rod design ensures equal 528 N clamping force at 0.5 MPa every cycle.
Set the exact electrode contact depth during commissioning. The M12x1.25 rod thread handles the 108 kgf max load while the adjustable stop screw locks the final position.
Confirm this 40 mm bore suits your load; the 40 mm adjustment window covers an effective 160-200 mm stroke. If you need less force, stepping down to the 32 mm bore yields 345 N at 0.5 MPa both ways. If your load is heavier, stepping up to the 50 mm bore provides 825 N at 0.5 MPa. If you never need to vary the end position, a fixed-stroke SED saves complexity.
The adjustable air cushion only decelerates the load near the end of travel; it is not a lock. A plain SEJ does not hold position on air loss, so specify a BSED or an external rod lock for fail-safe holding. At 200 mm stroke, guide external loads to prevent side-loading the Ø16 mm rod. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Quick checklist
A stop screw on the back rod lets you mechanically shorten the retract stroke by up to 40 mm. This gives an effective stroke range of 160 to 200 mm. You dial in the exact end position during commissioning and lock it down without swapping cylinders.
Because it is a double-rod cylinder, the force is identical in both directions. It provides 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.