verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ40X200-50S

The AirTAC SEJ Adjustable Cylinder SEJ40X200-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø40mm unit covers an effective stroke of 150–200mm without changing cylinders. Force is equal in both directions.

  • BoreØ40 mm
  • Nominal stroke200 mm
  • Adjust window50 mm
  • Effective stroke150–200 mm
  • Port sizePT1/4
  • CushionAdjustable, 30 mm
$89.29 $96.79Save 7% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SEJ40 stroke, mounting and version on one page All SEJ40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SEJ Adjustable Cylinder SEJ40X200-50S

The AirTAC SEJ40X200-50S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, ensuring the annulus area is identical in both directions. This yields an equal drive force of 528 N each way at 0.5 MPa, eliminating speed and force disparities between extend and retract strokes.

This variant features a 50 mm adjustable stroke window. A mechanical stop screw on the rear rod lets you dial the retract end from 150 mm up to 200 mm. The extruded aluminum barrel has no external tie rods, operating at 30-800 mm/s with PT1/4 ports and a Ø16 mm rod. The built-in magnet supports CMSE reed and DMSE electronic sensors for position feedback.

Airtac SEJ Adjustable Cylinder SEJ40X200-50S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ40X200-50S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ40 mm
Nominal stroke200 mm
Adjustment window50 mm (150–200 mm)
ConfigurationDouble rod, double acting
Port sizePT1/4
Rod threadM12×1.25
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressureForce (both directions)
0.5 MPa528 N
0.7 MPa739 N
Max (@1.0 MPa)108 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ40X200-50S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
40Bore size in mm.
×200Nominal stroke length in mm.
-50Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ40X200-50S Is Used

tune

Press Stroke Calibration

Dial the retract stop precisely during machine commissioning to set a 165 mm pressing depth, utilizing the 528 N both-way force without swapping hardware.

Is the Airtac SEJ Adjustable Cylinder SEJ40X200-50S the Right Cylinder?

Verify the 50 mm adjustment window covers your required end-position range. If you need less fine-tuning, a fixed-stroke SED saves cost; if you need higher clamping force, step up to the 50 mm bore (1154 N both ways at 0.7 MPa). Stepping down to the 32 mm bore yields 483 N at 0.7 MPa. For a direct ISO 15552 replacement, match the 200 mm stroke, 50 mm window, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Note that the air cushions decelerate the load near stroke end but do not hold position on air loss; use an external rod lock for fail-safe holding. At 200 mm stroke, ensure external guides manage side loads to protect the Ø16 mm rod.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (50mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 50mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ40X200-50S FAQ

A stop screw on the rear extending rod mechanically shortens the retract stroke over a 50 mm window. You can dial the effective stroke anywhere from 150 mm up to the full 200 mm, then lock the screw in place. This allows on-machine fine-tuning of the end position without changing the cylinder hardware.

Because it is a double-rod cylinder, the force is identical in both directions. It provides 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ40X200-50S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SEJ40X200-50S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.