
The AirTAC SEJ Adjustable Cylinder SEJ40X25-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø40mm unit covers an effective stroke of 5–25mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X25-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window, yielding a 5-25mm effective stroke range. A rod exits both ends, ensuring the annulus area is identical in both directions. This delivers an equal force of 528 N at 0.5 MPa and 739 N at 0.7 MPa each way, avoiding the asymmetric push/pull forces of single-rod units.
You dial in the retract end position via a stop screw on the back rod, then lock it down for precise machine commissioning. The extruded aluminum barrel has no external tie rods, and the -S magnet supports CMSE reed and DMSE electronic sensors for end-of-stroke detection. Field-adjustable air cushions at both ends decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X25-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 25 mm |
| Adjustment window | 20 mm (5–25 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×25 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 5-25mm retract end to match different adhesive bead heights during product changeover, using the equal 739 N both-way force at 0.7 MPa to lift and seat the valve.
Fine-tune the testing depth of a 16mm rod probe against delicate electronics during commissioning, locking the stop screw once the exact contact point is found.
Set the exact mechanical stop for a light clamping fixture, adjusting the end position on the machine without swapping out physical hardware for each new part.
Confirm this 20mm adjustment window covers your required end-position variance. If you need less force, the 32mm bore delivers 345 N at 0.5 MPa; if you need more, the 50mm bore provides 825 N at 0.5 MPa. If your stroke never changes, a fixed-stroke SED saves complexity. For replacing an ISO 15552 cylinder, match the 25mm stroke, PT1/4 port, and your mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Note: the adjustable cushion and stop screw decelerate and set the mechanical end, but this cylinder does not hold position on air loss. For fail-safe holding, use an external rod lock or BSED.
Quick checklist
The SEJ40X25-20S has a stop screw on the back rod that lets you dial the retract end up to 20mm. The effective stroke range is 5-25mm, allowing you to fine-tune the end position directly on the machine during commissioning.
Because it is a double-rod cylinder, the force is identical in both directions. It delivers 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.