verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ40X250-10S

The AirTAC SEJ Adjustable Cylinder SEJ40X250-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø40mm unit covers an effective stroke of 240–250mm without changing cylinders. Force is equal in both directions.

  • BoreØ40 mm
  • Nominal stroke250 mm
  • Adjust window10 mm
  • Effective stroke240–250 mm
  • Port sizePT1/4
  • CushionAdjustable, 30 mm
$96.27 $103.77Save 7% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SEJ40 stroke, mounting and version on one page All SEJ40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SEJ Adjustable Cylinder SEJ40X250-10S

The AirTAC SEJ40X250-10S is a double-acting, double-rod ISO 15552 profile cylinder with a 10mm adjustable stroke window, yielding an effective travel range of 240-250mm. The integrated magnet (-S) supports CMSE reed and DMSE electronic sensors for precise position detection.

A mechanical stop screw on the back rod lets you dial in the retract end-position during machine commissioning without swapping hardware. The extruded aluminum barrel contains no external tie rods, and adjustable air cushions at both ends decelerate the load near stroke end. This cylinder uses a PT1/4 port and a Ø16mm rod with an M12x1.25 thread.

Airtac SEJ Adjustable Cylinder SEJ40X250-10S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ40X250-10S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ40 mm
Nominal stroke250 mm
Adjustment window10 mm (240–250 mm)
ConfigurationDouble rod, double acting
Port sizePT1/4
Rod threadM12×1.25
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø40mm)

PressureForce (both directions)
0.5 MPa528 N
0.7 MPa739 N
Max (@1.0 MPa)108 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ40X250-10S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
40Bore size in mm.
×250Nominal stroke length in mm.
-10Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ40X250-10S Is Used

precision_manufacturing

Packaging Stop Dial-In

Fine-tune the 240-250mm retract position on packaging lines to match carton heights precisely, leveraging the 528N both-way force to push and pull folding mechanisms.

settings

Machine Changeover

Adjust the 10mm stop screw during product format changes on fillers, using the equal push-pull force to reposition guide rails without swapping cylinders.

science

Trial Positioning Jig

Use the double-rod design in R&D jigs to test clamping pressure at 0.5 MPa, dialing the end stop to test multiple part depths before finalizing the stroke.

Is the Airtac SEJ Adjustable Cylinder SEJ40X250-10S the Right Cylinder?

Verify the 10mm adjustment window covers your required end-stop range. If 528N at 0.5 MPa is insufficient, stepping up to the 63mm bore yields 1402N both ways; if oversized, the 32mm bore provides 345N. For fixed-stroke needs without the back-rod adjuster, the SED series is a simpler alternative.

This unit does not hold position on air loss—the cushion and stop screw only set the mechanical end and decelerate the load. For fail-safe holding, use an external rod lock or BSED. Because the 250mm stroke exceeds 300mm, ensure external guides support side loads to prevent rod binding. Match ISO 15552 replacements by confirming bore, stroke, port, and mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2).

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (10mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 10mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ40X250-10S FAQ

A stop screw on the back rod mechanically shortens the retract stroke over a 10mm window. You can dial the effective stroke from 240mm up to 250mm, then lock the screw in place to secure the exact end position.

Because the rod exits both ends, the annulus area is identical in both directions. It generates 528N at 0.5 MPa, 739N at 0.7 MPa, and a maximum of 108kgf at 1.0 MPa for both extend and retract.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ40X250-10S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SEJ40X250-10S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.