
The AirTAC SEJ Adjustable Cylinder SEJ40X250-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø40mm unit covers an effective stroke of 230–250mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X250-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window, allowing you to dial the retract end from 230mm to 250mm. A rod exits both ends, yielding identical annulus areas so output force stays equal in both directions at 528 N at 0.5 MPa.
Because the stroke exceeds 300mm is not met here but the 250mm length still warrants care, the M12x1.25 rod ends require external guides to prevent side-load wear. The built-in magnet supports CMSE reed and DMSE electronic sensors, while field-adjustable air cushions at both ends decelerate the load smoothly.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X250-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 250 mm |
| Adjustment window | 20 mm (230–250 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×250 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20mm retract window to set precise 230-250mm contact depth on PCB pins, using the 739N both-way force at 0.7 MPa without re-mounting hardware.
Switch carton forming stops for different box heights by adjusting the back-rod screw, leveraging the 528N equal force to consistently fold flaps.
Fine-tune the exact adhesive bead dispense volume during commissioning by trimming the effective stroke, relying on DMSE electronic sensors for confirmation.
Verify the 20mm adjustment window covers your positioning range; if you need less fine-tuning, a fixed-stroke SED saves cost. For sizing, the next bore down (32mm) yields 345 N at 0.5 MPa, while stepping up to a 50mm provides 825 N both ways. This SEJ40X250-20S delivers 528 N at 0.5 MPa.
The adjustable air cushion and mechanical stop screw set the end position but do not hold the load on air loss; for fail-safe locking, specify a BSED or an external rod lock. Dimensional ISO 15552 replacement requires matching the 40mm bore, 250mm stroke, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke over a 20mm window, making the effective stroke 230mm to 250mm. You lock the screw after setting the exact end position needed on the machine.
Because it is a double-rod cylinder, force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.