
The AirTAC SEJ Adjustable Cylinder SEJ40X250-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø40mm unit covers an effective stroke of 220–250mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X250-30S is a double-acting, double-rod ISO 15552 profile cylinder with a 30 mm adjustable stroke window. A rod exits both ends, making the annular area identical and delivering an equal force of 528 N each way at 0.5 MPa. You can dial the retract end from 220 mm up to the 250 mm nominal stroke.
A stop screw on the back rod sets the mechanical end position, which you lock after fine-tuning the machine commissioning spot. The extruded aluminum barrel has no external tie rods, and the -S magnet supports CMSE reed and DMSE electronic sensors for end-position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X250-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 250 mm |
| Adjustment window | 30 mm (220–250 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×250 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dialing the 30 mm retract window lets you fine-tune the exact 220-250 mm stop position for sheet metal feed lengths, using the 528 N both-way force to hold the guide precisely.
During machine commissioning, set the back-rod stop screw to test component insertion depths, locking the cylinder once the optimal 220-250 mm travel is found.
Verify the 30 mm window covers your positioning range before selecting this 40 mm bore. If you need less force, the 32 mm bore gives 345 N both ways at 0.5 MPa; if you need more clamping power, step up to the 50 mm bore for 825 N both ways. If your machine never requires stroke adjustment, a fixed-stroke SED cylinder provides the same equal-force dynamics in a shorter overall length.
This SEJ40X250-30S uses a PT1/4 port and a Ø16 mm rod with an M12x1.25 thread. Remember that the adjustable air cushion only decelerates the load near stroke end; it is not a brake. A plain SEJ will not hold position on air loss, so specify a BSED or an external rod lock for fail-safe holding. Since the stroke is 250 mm, ensure external guides support the load to prevent rod side-loading.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 30 mm window. You can set the effective stroke anywhere from 220 mm up to the 250 mm nominal stroke, then lock it for consistent operation.
Because the rod exits both ends, force is equal in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.