
The AirTAC SEJ Adjustable Cylinder SEJ40X250-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø40mm unit covers an effective stroke of 210–250mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X250-40S is a double-acting, double-rod ISO 15552 profile cylinder with a 40 mm adjustment window, letting you dial the retract stroke precisely between 210 and 250 mm. A mechanical stop screw on the back rod sets the end point, which you lock down after positioning. Because the rod exits both ends, the annulus area is symmetrical, delivering equal force and speed in both directions at 528 N each way at 0.5 MPa.
This extruded-aluminum profile cylinder omits external tie rods and includes a built-in magnet for position sensing. It features field-adjustable air cushions at both ends to decelerate the load near the stroke extremes. The Ø16 rod uses an M12x1.25 thread, and the PT1/4 porting keeps airflow high across its 30-800 mm/s speed range.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X250-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 250 mm |
| Adjustment window | 40 mm (210–250 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×250 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 40 mm window to switch part heights on packaging equipment, using the 739 N both-way force to push and pull tooling without re-mounting hardware.
Fine-tune the retract stop during stamping press commissioning, hitting a precise 210-250 mm end point to test material feed before locking the back rod.
Adjust the retract stroke on a conveyor sorting gate to handle different carton widths, relying on equal push/pull speed for stable diversion.
Confirm this 40 mm bore hits your target within the 210-250 mm effective range; if you need less force, step down to the 32 mm bore (345 N both ways at 0.5 MPa), or step up to the 50 mm bore (825 N both ways) for higher loads. If your end position never changes, a fixed-stroke SED saves cost. The adjustable cushion is for deceleration only; a plain SEJ will not hold position on air loss, so use an external rod lock for fail-safe holding. At 250 mm stroke, guide external loads to prevent side-load damage to the M12x1.25 rod thread. Match ISO 15552 replacements by bore, stroke, 40 mm window, PT port, and mounting (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
A stop screw on the back rod lets you mechanically shorten the retract stroke by up to 40 mm. The effective stroke range is 210 to 250 mm. You set the exact end position on the machine, then lock the screw.
Because the rod exits both ends, force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.