
The AirTAC SEJ Adjustable Cylinder SEJ40X250-75 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø40mm unit covers an effective stroke of 175–250mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X250-75 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm adjustable stroke window. By dialing the stop screw on the back rod, you set the effective travel anywhere from 175 mm up to the full 250 mm.
Because the retract end is mechanically variable, you can fine-tune the machine stop during commissioning without swapping hardware. The extruded aluminum barrel contains no external tie rods, and adjustable air cushions at both ends decelerate the load near stroke end. This SKU lacks a piston magnet, so it carries no position sensor.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X250-75 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 250 mm |
| Adjustment window | 75 mm (175–250 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×250 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 175-250 mm stroke range to fine-tune the stopping position of cartons on a packaging conveyor, using the 528 N both-way force to halt loads securely.
Quickly reposition the retract end by up to 75 mm to accommodate different product heights on a changeover line, avoiding the need to physically remount the actuator.
Verify the 75 mm adjustment window covers your required end-position range. If 528 N at 0.5 MPa is excessive, step down to the 32 mm bore (345 N both ways); if you need more push, step up to the 50 mm bore (825 N both ways). For fixed travel without the back-rod adjuster, a standard SED double-rod cylinder is sufficient. Remember that the air cushion and mechanical stop screw decelerate the load and set the end point, but a plain SEJ does not hold position on air loss; for fail-safe holding, use an external rod lock. Since the 250 mm stroke exceeds 300 mm? No, but at 250 mm you should still ensure the load is guided to prevent side-load bending on the 16 mm rod. Match your ISO 15552 replacement by confirming the PT1/4 port, 30 mm cushion length, and preferred mounting from the Basic, FA, LB, TC, FTC, TCM1, or TCM2 set.
Quick checklist
The 75 mm adjustment window allows you to dial the retract stroke from a minimum effective travel of 175 mm up to the full nominal stroke of 250 mm. You set the exact end position via the stop screw on the back rod and lock it in place.
Because the rod exits both ends, the force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.