
The AirTAC SEJ Adjustable Cylinder SEJ40X275-75 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø40mm unit covers an effective stroke of 200–275mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X275-75 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm adjustable stroke window. A rod exits both ends, meaning the annulus area is identical in both directions, yielding an equal force of 528 N each way at 0.5 MPa. You can dial the retract end from 200 mm up to the nominal 275 mm.
A mechanical stop screw on the back rod lets you fine-tune the end position during machine commissioning and lock it in place. The extruded aluminum barrel has no external tie rods, and field-adjustable air cushions at both ends decelerate the load near stroke end. This SKU has no magnet, so it will not support CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X275-75 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 275 mm |
| Adjustment window | 75 mm (200–275 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×275 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the retract stroke up to 75 mm to match varying sheet metal flange depths on a press brake, using the 528 N both-way force to position the stop accurately.
Adjust the effective stroke between 200 and 275 mm to handle different carton heights on a packaging line without swapping out the entire cylinder assembly.
Fine-tune the end position during machine commissioning to find the exact 40 mm bore clamping point, then lock the back-rod stop screw for repeatable cycles.
Confirm the 75 mm adjustment window covers your required end-position range. If you need less fine-tuning, a fixed-stroke SED40 is simpler and sufficient. For sizing both ways: the next bore down (32 mm) gives 345 N at 0.5 MPa, while the next bore up (50 mm) yields 825 N at 0.5 MPa. Since the 275 mm stroke exceeds 300 mm, use external guides to prevent side-loading on the rod. Remember, the air cushion and stop screw are not brakes; a plain SEJ will not hold position on air loss, so use a BSED or external rod lock for fail-safe holding. To replace an ISO 15552 cylinder, match the 40 mm bore, 275 mm stroke, PT1/4 port, and mounting (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
The retract end can be dialed up to 75 mm. The effective stroke range is 200 mm to the nominal 275 mm. You set the mechanical stop screw on the back rod to the exact position required and lock it in place.
Because it is a double-rod cylinder, the force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa. It is dimensionally interchangeable per ISO 15552.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.