
The AirTAC SE40 Standard Cylinder SE40X275 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 275mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X275 is a double-acting single-rod profile cylinder built to the ISO 15552 / VDMA 24562 standard. It delivers 628 N of push force at 0.5 MPa and utilizes a PT1/4 port with a 16 mm rod. Because this SKU lacks the -S magnet suffix, it is not equipped for direct CMSE or DMSE position sensing without modification.
The extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames and shrinks overall installation width. Field-adjustable air cushions at both stroke ends allow technicians to tune deceleration via a set screw, softening hard end-stops when cycling at speeds up to 800 mm/s.
| Model | Airtac SE40 Standard Cylinder SE40X275 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 275 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×275 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Gates and diverts lightweight PET bottles on a high-speed packaging conveyor, utilizing the 628 N push force and 275 mm stroke to clear product lanes efficiently.
Folds secondary corrugated carton flaps prior to case sealing, where the 528 N retract force reliably tucks material without crushing the board.
Pushes empty printed circuit board trays into a testing fixture, relying on the adjustable end-cushions to prevent jarring impacts at 800 mm/s.
When sizing this 40 mm bore, stepping down to a 32 mm bore drops the 0.5 MPa push force to 402 N, whereas stepping up to a 50 mm bore raises it to 982 N. This SE40X275 provides 628 N push and 528 N pull, making it a solid mid-range choice. If your application must hold a load vertically without live air pressure, note that a standard SE cylinder will drift; you should pivot to a BSE rod-lock variant or employ an external pilot-operated check valve.
Because the 275 mm stroke is non-standard and exceeds the typical 250 mm increment, it is supplied as a made-to-order unit. For an unsupported stroke of this length, the 16 mm rod and M12x1.25 thread face increased bending moments; always support the load with an external guide to prevent side-load damage to the rod bearing. As a true ISO 15552 cylinder, it is dimensionally interchangeable with other ISO 15552 profile cylinders for straightforward retrofits.
Quick checklist
The SE40X275 provides 628 N push and 528 N pull at 0.5 MPa, 879 N push at 0.7 MPa, and a maximum push of 128 kgf at 1.0 MPa. It operates at speeds ranging from 30 to 800 mm/s.
Yes. The SE40X275 shares the exact ISO 15552 / VDMA 24562 mounting interface and dimensions, allowing it to serve as a direct replacement for other standard ISO 15552 profile cylinders using your existing mounting hardware.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.