
The AirTAC SEJ Adjustable Cylinder SEJ40X450-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø40mm unit covers an effective stroke of 350–450mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X450-100S is a double-acting, double-rod ISO 15552 profile cylinder. A 16mm rod exits both ends, yielding identical annulus areas so output force is exactly 528 N each way at 0.5 MPa. The 100mm retract stop-screw window sets an effective stroke range of 350-450mm, letting you dial in a precise end position without machining new hardware.
Because the stroke is 450mm, the twin rods provide better guidance against side-load induced bowing than a single rod. The extruded aluminum barrel carries no external tie rods, and field-adjustable air cushions at both ends decelerate the 30-800 mm/s motion. The installed -S magnet supports CMSE reed or DMSE electronic sensors for position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X450-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 450 mm |
| Adjustment window | 100 mm (350–450 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×450 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 100mm retract window to perfectly sync a 450mm feed stroke during machine commissioning, using the equal 739 N both-way force at 0.7 MPa to push and pull the material carriage.
Rapidly adjust the effective stroke from 350 to 450mm to accommodate different package heights on a sealing head, avoiding the need to swap out the entire cylinder.
Confirm the 100mm adjustment window covers your positioning range. If 528 N at 0.5 MPa is insufficient, step up to the 50mm bore (825 N both ways); if oversized, step down to the 32mm bore (345 N). If your stop position never changes, a fixed-stroke SED is simpler. Note: the stop screw and air cushions only set the mechanical end and decelerate near stroke end; a plain SEJ does not hold position on air loss. For fail-safe hold, use a BSED or an external rod lock.
For ISO 15552 replacement matching, verify the 40mm bore, 450mm nominal stroke, 100mm window, PT1/4 port, and your specific mounting (Basic, FA, LB, TC, FTC, TCM1, or TCM2). At 450mm stroke, mount external guides to absorb any lateral load and prevent rod binding.
Quick checklist
The 100mm adjustment window lets you mechanically shorten the retract stroke. The effective range is 350-450mm. You dial the back-rod stop screw to the required position, then lock it in place.
Because the rod exits both ends, force is equal in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.