
The AirTAC SEJ Adjustable Cylinder SEJ40X50-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø40mm unit covers an effective stroke of 40–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X50-10S is a double-acting, double-rod ISO 15552 profile cylinder with an adjustable retract stroke. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 528 N (0.5 MPa). The back rod features a mechanical stop screw that lets you dial the retract end over a 10 mm window, providing an effective stroke range of 40-50 mm.
This adjustability eliminates the need to swap hardware when fine-tuning an end position during machine commissioning. The extruded aluminum barrel has no external tie rods, and adjustable air cushions at both ends decelerate the load near stroke end. The included -S magnet enables position detection with CMSE reed or DMSE electronic sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X50-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 10 mm (40–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 40-50 mm retract distance on an automated gripper arm during commissioning, using the 528 N both-way force to securely clamp parts without over-traveling.
Quickly adjust the end-of-stroke stop by up to 10 mm to accommodate varying product heights on a packaging conveyor, avoiding the need to physically swap out the cylinder.
Fine-tune the electrode touch position on a small spot welding fixture, relying on the equal 739 N extend and retract force at 0.7 MPa for consistent electrode pressure.
Verify the 10 mm adjustment window covers your positioning range, setting the effective stroke anywhere from 40 to 50 mm. If you need less force, the adjacent 32 mm bore provides 345 N at 0.5 MPa; if you need more, stepping up to the 50 mm bore yields 825 N both ways. If the exact end position is already fixed and never changes, a standard SED double-rod cylinder is sufficient.
The adjustable air cushion and stop screw decelerate the load and set the mechanical end, but a plain SEJ does not hold position on air loss. For fail-safe holding, use an external rod lock. This cylinder is dimensionally interchangeable per ISO 15552; match the 40 mm bore, 50 mm nominal stroke, PT1/4 port, and mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) for a direct replacement.
Quick checklist
The retract end features a stop screw on the back rod that allows you to adjust the stroke over a 10 mm window. For this 50 mm nominal stroke model, the effective retract stroke can be dialed in from 40 mm up to 50 mm. You lock the screw in place once the desired end position is reached.
Because a rod exits both ends, the force is identical in both directions. At 0.5 MPa it provides 528 N, at 0.7 MPa it provides 739 N, and the maximum force is 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.