
The AirTAC SEJ Adjustable Cylinder SEJ40X50-30S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 30mm window, so this Ø40mm unit covers an effective stroke of 20–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X50-30S is a double-acting, double-rod ISO 15552 profile cylinder with a 30 mm adjustable stroke window. A stop screw on the rear rod lets you dial the retract end position, yielding an effective stroke range of 20 to 50 mm without swapping hardware.
This 40 mm bore unit runs at 30-800 mm/s and features field-adjustable air cushions at both ends to manage deceleration. The -S magnet enables position detection with CMSE reed or DMSE electronic sensors. The extruded aluminum barrel omits external tie rods for a clean profile, and the rear rod can carry a cam for external tracking.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X50-30S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 30 mm (20–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 30mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -30 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20-50 mm retract position to pick parts from varying pallet heights. The equal 528 N both-way force ensures secure lifting and lowering without thrust imbalance.
Fine-tune the exact end-of-stroke contact point on a light assembly press during setup. The 30 mm window allows precise mechanical stop adjustment before locking the screw.
Adjust the stroke on the machine for different product lengths without changing cylinders. The integrated magnet works with DMSE sensors to confirm the new retracted position.
Verify the 30 mm adjustment window covers your required end-position variance; here you can tune the retract stroke anywhere from 20 mm up to the 50 mm nominal length. If you need less force, stepping down to the 32 mm bore yields 345 N at 0.5 MPa both ways. If your application requires more thrust, stepping up to the 50 mm bore provides 825 N at 0.5 MPa. If your machine never requires stroke adjustments, a fixed-stroke SED cylinder provides the same double-rod output more simply. Remember that the adjustable cushion and stop screw decelerate the load but do not hold position on air loss; for fail-safe holding, specify an external rod lock. Ensure your ISO 15552 replacement matches the PT1/4 port, M12x1.25 rod thread, and desired mounting from the SEJ set (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
A mechanical stop screw on the rear rod lets you shorten the retract stroke by up to 30 mm. This gives an effective stroke range of 20 to 50 mm, allowing you to fine-tune the end position directly on the machine before locking it in.
Because it is a double-rod cylinder, the force is identical in both directions. It provides 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.