
The AirTAC SEJ Adjustable Cylinder SEJ40X500-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø40mm unit covers an effective stroke of 480–500mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X500-20S is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, ensuring identical annulus area for equal force and speed in both directions. You get 528 N each way at 0.5 MPa and 739 N at 0.7 MPa. The integrated -S magnet supports CMSE reed and DMSE electronic sensors for position tracking.
A mechanical stop screw on the back rod provides a 20 mm adjustable stroke window. This lets you dial the retract end from 480 mm up to 500 mm during machine commissioning. The extruded aluminum barrel has no external tie rods, and adjustable air cushions at both ends decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X500-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 500 mm |
| Adjustment window | 20 mm (480–500 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×500 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20 mm retract window to perfectly match a sheet metal press feed stop, using the 739 N both-way force to consistently push the material.
Adjust the retract end on the fly to meet varying package heights on a packaging line, benefiting from equal push and pull forces.
Quickly reposition a 500 mm stroke pick-and-place actuator during product changeover without swapping hardware, locking the stop screw precisely.
Verify the 20 mm adjustment window covers your positioning range. If you need less push, the 32 mm bore yields 345 N both ways at 0.5 MPa; if you need more, step up to the 50 mm bore for 825 N. A fixed-stroke SED is sufficient if you do not require end-position tuning.
For a 500 mm stroke, external guides are recommended to prevent side loading on the rod. This cylinder does not hold position on air loss; use an external rod lock for fail-safe holding. It is dimensionally interchangeable per ISO 15552 with a PT1/4 port and M12x1.25 rod thread.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 20 mm. The effective stroke range is 480-500 mm. You set the exact end position on the machine and lock the screw.
Because it is a double-rod design, the force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.