
The AirTAC SE40 Standard Cylinder SE40X500 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 500mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X500 is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering 628 N of push force at 0.5 MPa and a maximum of 128 kgf at 1.0 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting the internal mechanics.
This 40 mm bore unit features a 500 mm stroke, a Ø16 mm piston rod, and PT1/4 ports. Field-adjustable pneumatic cushioning at both end caps allows technicians to tune the deceleration of the piston via a set screw, softening hard end stops during high-speed cycling. Note that this specific SKU lacks a built-in magnet, so it is not wired for CMSE or DMSE position sensing out of the box.
| Model | Airtac SE40 Standard Cylinder SE40X500 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 500 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Extends a 500 mm stroke to reroute flat pallets between parallel conveyor lines, utilizing the 628 N push force to overcome sliding friction without stalling.
Deploys a mechanical arm at the carton sealing station, providing reliable motion to tuck heavy cardboard flaps prior to tape application.
Ejects filled storage totes from an automated retrieval shuttle, relying on the 40 mm bore's 128 kgf maximum thrust to clear the payload smoothly.
When sizing this actuator, compare its 628 N push at 0.5 MPa against its neighbors: step down to the 32 mm bore for 402 N if the load is lighter, or move up to the 50 mm bore for 982 N if you need greater thrust margin. As a true ISO 15552 profile cylinder, the SE40X500 serves as a direct dimensional replacement for other ISO 15552 cylinders, matching standard mounting accessories like FA front flanges or LB foot brackets without requiring custom machined plates.
Because this model features a 500 mm stroke, the unsupported rod length increases susceptibility to bending under side loads; always incorporate an external linear guide to prevent premature rod-bearing wear. Furthermore, a standard double-acting cylinder drifts when air pressure is lost or the valve centers, so if your application must hold a vertical load safely without live pressure, integrate an external rod lock or pilot-operated check valve.
Quick checklist
At 0.5 MPa, the SE40X500 generates 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N, with an absolute maximum push capacity of 128 kgf at 1.0 MPa. The operational speed range for this 40 mm bore cylinder is 30-800 mm/s.
Yes, the SE40X500 is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders of the same bore and stroke, reusing existing mounting hardware like FA flanges or TC trunnions without altering the machine footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.