
The AirTAC SEJ Adjustable Cylinder SEJ40X500-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø40mm unit covers an effective stroke of 450–500mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X500-50S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50mm adjustable stroke window, letting you dial the retract end from 450mm to 500mm. A rod exits both ends, meaning the annulus area is identical in both directions for an equal force of 528 N each way at 0.5 MPa.
The rear rod carries a mechanical stop screw to set that precise end-position during machine commissioning, which you lock down after tuning. It includes a magnet for CMSE or DMSE sensors, adjustable air cushions at both ends, and a PT1/4 port. The extruded aluminum barrel has no external tie rods, ensuring clean ISO 15552 dimensional interchangeability.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X500-50S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 500 mm |
| Adjustment window | 50 mm (450–500 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×500 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 450-500mm retract stroke on the fly to match varying box sizes, using the equal 528N both-way force to push flaps squarely without skewing the load.
Swap part heights on a single fixture by adjusting the back-rod stop screw up to 50mm, avoiding hardware changes while maintaining 739N of precise clamping force at 0.7MPa.
Fine-tune the exact cutoff point during commissioning by locking the retract end exactly where the 16mm rod meets the extrusion head, ensuring repeatable volumetric dosing.
Confirm the 50mm adjustment window covers your required positioning range. If you need less force, the 32mm bore provides 345 N both ways at 0.5 MPa; if scaling up, the 50mm bore offers 825 N. For fixed-retract applications without fine-tuning, a standard SED cylinder is sufficient.
Because the 500mm stroke is long, add external guide rails to handle side loads and prevent rod binding. A plain SEJ does not hold position on air loss—the adjustable cushion only decelerates near stroke end, not a lock. For fail-safe holding, use an external rod lock. Match ISO 15552 replacements by bore, 450-500mm range, PT1/4 port, and mounting (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Quick checklist
The model features a 50mm adjustment window on the retract end via a back-rod stop screw. You can mechanically dial the effective stroke down from the nominal 500mm to 450mm, then lock it in place for precise end-positioning.
Because the rod exits both ends, force is equal in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa. Speed is 30-800 mm/s.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.