
The AirTAC SEJ Adjustable Cylinder SEJ40X60-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø40mm unit covers an effective stroke of 40–60mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X60-20S is a double-acting, double-rod ISO 15552 profile cylinder with a 20mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas and equal force in both directions—delivering 528 N at 0.5 MPa and 739 N at 0.7 MPa each way. The retract stroke dials from 40mm up to 60mm via a back-rod stop screw.
This extruded aluminum barrel omits external tie rods for a clean profile. The -S magnet option enables position detection with CMSE reed or DMSE electronic sensors. Adjustable air cushions at both ends decelerate the 16mm rod near stroke limits without locking it.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X60-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 60 mm |
| Adjustment window | 20 mm (40–60 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×60 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 40-60mm retract stop to perfectly set gripper jaw opening on varying part sizes, using the equal 739 N both-way force at 0.7 MPa.
Fine-tune the mechanical end position during commissioning to set precise pin insertion depths without reprogramming the machine.
Quickly adjust the stroke window for production line changeovers between different product heights, locking the back-rod screw once set.
Verify the 20mm adjustment window covers your end-position range. If 528 N at 0.5 MPa is excessive, step down to the 32mm bore (345 N); if insufficient, step up to the 50mm bore (825 N). For fixed-position tasks needing no fine-tuning, a standard SED double-rod cylinder suffices.
This cylinder does not hold position on air loss; use an external rod lock for fail-safe clamping. Ensure your ISO 15552 replacement matches the 40mm bore, 60mm nominal stroke, PT1/4 port, and chosen mounting from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke by up to 20mm. The effective stroke range is 40-60mm. You dial the end position during setup and lock the screw in place.
Because it is a double-rod cylinder, force is identical in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.