
The AirTAC SEJ Adjustable Cylinder SEJ40X600-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø40mm unit covers an effective stroke of 500–600mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X600-100S is a double-acting, double-rod ISO 15552 profile cylinder with a 100 mm adjustable stroke window, letting you dial the retract end anywhere from 500 to 600 mm. A rod exits both ends, yielding identical annulus areas so output force is perfectly balanced at about 528 N each way at 0.5 MPa. The included magnet (-S) supports CMSE reed and DMSE electronic sensors for precise end-position detection.
You tune the retract position via a stop screw on the back rod, then lock it down to match your machine stop exactly. This extruded aluminum profile cylinder features field-adjustable air cushions at both ends to decelerate the payload smoothly over the 30 mm cushion length, and its PT1/4 ports match the standard 40 mm bore architecture.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X600-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 600 mm |
| Adjustment window | 100 mm (500–600 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×600 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 500-600 mm retract to fold varying carton depths. The 528 N both-way force ensures positive folding pressure regardless of direction.
Quickly reposition the stop screw by up to 100 mm to accommodate different pallet heights during line changeovers without swapping hardware.
Use the adjustable end-stop to fine-tune adhesive dispense paths. The DMSE electronic sensor tracks the exact 600 mm extend position.
Verify the 100 mm adjustment window covers your required positioning range. If 528 N at 0.5 MPa is excessive, step down to the 32 mm bore delivering 345 N both ways; if you need more push, move up to the 50 mm bore providing 825 N both ways. A fixed-stroke SED cylinder is sufficient if your end-stop never changes. For direct ISO 15552 replacement, match the 600 mm stroke, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Because the 600 mm stroke is long, use external guides to prevent rod side-loading and premature seal wear. Note that the air cushions and stop screw decelerate the load but do not hold position on air loss; apply an external rod lock for fail-safe holding.
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 100 mm. The effective stroke range is 500 to 600 mm. You set the exact end-position during commissioning and lock the screw in place.
Because it is a double-rod cylinder, force is equal in both directions. It provides 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.