
The AirTAC SEJ Adjustable Cylinder SEJ40X600-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø40mm unit covers an effective stroke of 580–600mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X600-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window. A rod exits both ends, yielding equal force of 528 N each way at 0.5 MPa, and the retract stroke dials in from 580 to 600mm via a back-rod stop screw. The integrated -S magnet supports CMSE reed and DMSE electronic sensors for precise end-of-stroke detection.
Standard features include field-adjustable air cushions at both ends (30mm cushion length) to manage kinetic energy. Because the stroke is 600mm, external guide rails are strongly recommended to prevent rod sagging and side-load damage. The extruded aluminum barrel omits external tie rods, and mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X600-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 600 mm |
| Adjustment window | 20 mm (580–600 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×600 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the retract position precisely during machine commissioning to seat lathe chucks against a stop, utilizing the 528N both-way force.
Quickly adjust the 580-600mm effective stroke to accommodate different carton heights on a packaging conveyor without swapping hardware.
Fine-tune the exact test contact point on electronic component fixtures, using the equal extend and retract forces for consistent pressure.
Verify the 20mm adjustment window covers your target range. If you need less push, the 32mm bore provides 345 N both ways at 0.5 MPa; if scaling up, the 50mm bore yields 825 N both ways. If exact positioning is not required, a fixed-stroke SED saves cost. This cylinder does not hold position on air loss; for fail-safe holding, use an external rod lock. Ensure your ISO 15552 replacement matches the 40mm bore, 600mm stroke, PT1/4 port, and magnet specifications.
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke over a 20mm window. The effective stroke range is 580 to 600mm. You dial the end position during commissioning and lock it in place.
Because it is a double-rod cylinder, the force is equal in both directions: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.