
The AirTAC SEJ Adjustable Cylinder SEJ40X70-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø40mm unit covers an effective stroke of 50–70mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X70-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window. A rear stop screw lets you dial the retract end down, yielding an effective stroke range of 50-70mm for precise on-machine positioning. The extruded aluminum barrel has no external tie rods.
Because a rod exits both ends, the annular area is identical in both directions, delivering an equal force of 528N each way at 0.5 MPa. The -S magnet supports CMSE reed and DMSE electronic sensors, and field-adjustable air cushions at both ends decelerate the 16mm rod near stroke ends.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X70-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 70 mm |
| Adjustment window | 20 mm (50–70 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×70 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 50-70mm effective stroke to set exact adhesive dispense heights during commissioning, utilizing the 528N both-way force to lift the rod safely.
Adjust the retract stop to accommodate different carton sizes on a packaging line without swapping hardware, relying on equal push and pull forces.
Micro-adjust the end stop to trial-fit components against a fixture, locking the 16mm back rod once the exact 50-70mm position is found.
Confirm the 20mm adjustment window covers your end-position tuning needs, then verify the 528N both-way output at 0.5 MPa is sufficient. If you need less force, the adjacent 32mm bore provides 345N both ways; if you need more, step up to the 50mm bore for 825N. If you do not require variable stops, a fixed-stroke SED cylinder is sufficient. For fail-safe position holding on air loss, use a BSED or an external rod lock. This ISO 15552 dimensionally interchangeable replacement matches your 40mm bore, 70mm stroke, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Quick checklist
The 20mm adjustment window allows you to mechanically shorten the retract stroke using a back-rod stop screw. The effective stroke range is 50-70mm, which you set and lock during machine commissioning.
Because the rod exits both ends, force is equal in both directions: 528N at 0.5 MPa, 739N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.