
The AirTAC SE40 Standard Cylinder SE40X70 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø40mm bore and 70mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE40X70 is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a push force of 628 N at 0.5 MPa and an extend force of 879 N at 0.7 MPa. It features a 40 mm bore, a 70 mm stroke, and a PT1/4 port. The square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion.
This model relies on field-adjustable pneumatic cushioning at both ends to decelerate the piston near stroke end, allowing you to tune out hard mechanical impacts at operating speeds up to 800 mm/s. Because this specific SKU lacks the -S magnet code, it does not support direct CMSE or DMSE position sensing without modification. The core body serves as the foundation for SED double-rod and SEJ adjustable-stroke variants.
| Model | Airtac SE40 Standard Cylinder SE40X70 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 70 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the mechanical arms that tuck minor flaps on corrugated packaging lines, utilizing the 628 N push force and 70 mm stroke for precise, compact cycling.
Actuates short-stroke routing gates on package conveyors, where the tie-rod-free aluminum profile mounts flush into tight framework and cycles at high speeds.
Applies downward clamping pressure on electronic test beds, using the 879 N extend force at 0.7 MPa to secure boards without flexing the panel.
When sizing this 40 mm bore, compare its 628 N push at 0.5 MPa against the 32 mm bore (402 N) if your payload is lighter, or step up to the 50 mm bore (982 N) for heavier lifting. This SE40X70 ships without a magnet, so if your sequence control requires end-of-stroke confirmation, specify the SE40X70S variant for CMSE reed or DMSE electronic sensor compatibility. As a true ISO 15552 profile cylinder, it serves as a direct replacement for any standard 40 mm bore with a 70 mm stroke, matching standardized mounting dimensions exactly.
Note that the integrated air cushion only softens end-of-stroke impacts; it does not hold the load if air pressure drops. If your application requires positive position holding upon loss of air, explore the BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
At 0.5 MPa, the SE40X70 provides 628 N of push force and 528 N of pull force. At 0.7 MPa, the push force increases to 879 N. The maximum push force is 128 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE40X70 is dimensionally interchangeable per ISO 15552 standards. You can use it as a direct replacement for other 40 mm bore profile cylinders with a 70 mm stroke, utilizing standard mounting accessories and the PT1/4 port.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.