
The AirTAC SEJ Adjustable Cylinder SEJ40X75-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø40mm unit covers an effective stroke of 25–75mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X75-50S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so output force is perfectly balanced at 528 N each way at 0.5 MPa. You can dial the retract end from 25 mm up to the nominal 75 mm stroke.
The retract position is set via a mechanical stop screw on the back rod, which you lock down after fine-tuning the machine end-state. Because it carries the S option, a built-in magnet enables position detection with CMSE reed or DMSE electronic sensors. The extruded aluminum barrel omits external tie rods, and adjustable air cushions at both ends safely decelerate the 16 mm rod near stroke extremes.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X75-50S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 75 mm |
| Adjustment window | 50 mm (25–75 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×75 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 50 mm retract window to match varying product thicknesses on a pick-and-place unit, using the equal 528 N both-way force to lift and lower without thrust imbalance.
Adjust the effective stroke from 25 to 75 mm during format changeovers on a packaging line, locking the back-rod stop screw once the exact end-position is found.
Fine-tune the pressing depth on a light assembly press, relying on the 739 N retract force at 0.7 MPa to consistently form parts without re-engineering fixed stops.
Verify the 50 mm adjustment window covers your required positioning range, letting you dial the retract stroke precisely between 25 and 75 mm during commissioning. If you need less force, stepping down to the 32 mm bore provides 345 N at 0.5 MPa both ways. If your application requires more thrust, stepping up to the 50 mm bore yields 825 N at 0.5 MPa both ways. If the end position never changes after initial setup, a fixed-stroke SED offers a simpler alternative.
This cylinder uses a PT1/4 port and matches standard ISO 15552 mounting dimensions. It supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, but omits FB, CA, CB, and CR brackets. Note that the adjustable cushion and mechanical stop screw only set the end-state and decelerate the load; they do not function as a fail-safe brake. For position holding upon air loss, specify an external rod lock.
Quick checklist
The -50 designation means you can adjust the retract stroke over a 50 mm window. The effective stroke ranges from 25 mm up to the nominal 75 mm. You set the exact end-position using a stop screw on the rear rod, then lock it in place.
Because it is a double-rod cylinder, the force is identical in both directions. It generates 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.